... If its really an 88 TC T5, it will have a bellhousing for a hydraulic clutch which is why you don't see anywhere to connect your cable to. ... Correct,...
This is an automatic mailing from the Ford Pinto Mailing List. Please read the rules and save this email as it contains important information including how to...
pinto@yahoogroups.com
Dec 1, 2006 2:48 pm
22563
... What about the brackets for the control arms that the Pinto does not have? What about the Mustang's width, which s more than the Pinto? ... Cheap Talk?...
Thanks Dave- So it seems then that I'm good with my new driven gear. As long as the T5 already has a 6 tooth drive gear installed, that should be easy if the...
... Cut them off. ... Deep offset wheels. Like I said in the other post, the Mustang rear is not a good choice, but it can be, and has been used in Pinto's...
... this T5 bellhousing work? I get the impression it will not from all of my reading. I heard an early-mid 80's mustang w/ T5 bellhousing will work. What...
Thanks Bug- I guess I'll go looking for one of those bell-housings, and I'll leave the ring-plate off. I'll also be sure to replace the pilot bearing. Thanks...
Okay- I got out in the garage and took a good look at the tip of the input shaft on the T5. There is a bit of surface rust on it, which kind of makes me...
... on the T5. There is a bit of surface rust on it, which kind of makes me nervous. Do you guys know if this is the sort of thing that can just "sand" off...
About the greater width of the late model Mustang rear - note that Bug did *not* recommend using the late Mustang rear - he said it *could* be used *if*...
Hi Kit, About the 6 tooth speedometer drive gear. It depends what year your tranny is - and what rear axle ratio the car that the tranny came out of...
Thanks guys- I'll look into a new front bearing retainer. I think the rust on the input shaft is fairly superficial. If I find after I go to work on it that...
Hey Group. I'm having some trouble with my '88 F150. YEAH, I know that this group is for the Pinto but I believe the trouble is with the fuel-injection system...
Hey Gerald, I`ve had the same problem with my Aerostar and Mazda...a can of fuel injector cleaner every month or two alway`s clear`s it up! Just my 2...
Hey all, how's it going. I'm in a bit of a pickle here. I'm replacing the valve cover gasket on my '79 bobcat 2.3 and I got the Felpro blue rubber gasket (#...
... truck has always had an occasional "surging idle" problem, then after a couple of minutes or about a mile or so it loses some power untill it warms up...
... rubber ... cover ... before? ... Thanx ... I just installed that type of gasket on my 2.3 in an 88 Mustang. My valve cover doesn't have the 2 extra bolts....
Not sure if you got a response already but the Fox Mustang rears are coil spring. They don't directly swap to the Pinto. You can get one from another Pinto or...
dose any make or sell reproduction ford pinto parts i am redoing a 76 runabout i am droping a v8 in it what i need is in some body parts, lights and a lot of...
Maybe Mr Rourke can help. Da PLANE! Da PLANE! ... __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best...
... 76 ... Michael, i have a gas tank and front and rear chrome bumpers for a 76 runabout also have one rear taillight in good condition. Items are in pa near...
Hi y'all I just recently got through with my floorpans/carpet/interior project and I'm happily driving my '75 Bobcat again and have just got the go ahead from...
... Mine was the same way until it finally broke, at which time, I discovered that the Mustang cable is exactly the same. ... Any questions? Get answers on...
Hey Bug- It's Kit again. I called Hanlon and told them what tranny I had. The id tag on it says 1352-155 (from an '87 2.3T t-bird). The lady I talked to...
... is the gas pedal is a bit hard to press down and I was wondering if there is any way to adjust the stiffnes of it.> ... discovered that the Mustang cable...
... Fox Mustang. The Mustang II is the same cable as the Pinto. ... The Pinto cable is the old style that is clad in spun wire and thin plastic. These tend to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
