This is an automatic mailing from the Ford Pinto Mailing List. Please read the rules and save this email as it contains important information including how to...
pinto@yahoogroups.com
Sep 1, 2004 5:49 pm
18591
HOWDY I STILL HAVE NOT TOTALY DECIDED WHAT I WANT TO FOR AN ENGINE IN 71 PINTO. LON LONG TIME BEFORE I DO A 302. I KNOW THAT FOR A FACT DOES ANY BODY IN TEXAS...
i have a big problem dont espeack in english, i have a pinto model 71and i need four piston for a engine 1600cc in a estandar ... Do You Yahoo!? Yahoo! Net:...
jose luis mendez
maxtosb@...
Sep 3, 2004 4:32 pm
18593
I have a 302 with a o/drive and when it goes into o/d it starts to tremor and shake...does anyone know what is causing this? Clarence Surf City,NC...
What is the speed you are traveling when it does this problem, and does it do it only when it is shifting into the O/D? or does this the whole time while in...
Sounds to me like the rearend gears are too high for overdrive maybe? Kinda like when shifting a manual into the next lower gear too soon - same thing. This...
... You're torque converter is going bad. The lockup clutch is shuddering. "Sometimes" this can be sured by a trans flush and filter change, but only if the...
my Thunderbird kinda does that if its AOD goes into 4th below 65 mph...my solution is to simply leave it in D for speeds below 65, and go 75 on the freeway:) ...
On a stock, unmodified T-Bird, you shouldn't need to be over 65 mph to use O.D, at least not on flat level ground. You're using a lot of extra fuel and adding...
Jose, Venolia pistons makes them. Venolia part number 4400. Be sure to specify standard bore, if that is the size you want. They are on the web at: ...
... O.D, at least not on flat level ground. You're using a lot of extra fuel and adding a lot of unnecessary wear and tear. If the tranny won't stay and run ...
mine's an '88...buying a TKO from a buddy of mine when he installs the T56 into his 'stang, so I'm not terribly worried about the trans. the car does still get...
The members who answered my question were just what I was looking for..a spot to start ....I have a 306...aod...8.8...3.73 gears..a 2800 stall (used) the motor...
... spot to start ....I have a 306...aod...8.8...3.73 gears..a 2800 stall (used) the motor has no miles with break in oil and a used aod...I have not service...
Read the last bunch of replies concerning AOD shudder. In three seperate un-related cases, trans shudder was a problem here in TX, as described in the original...
It was just a matter of time. (SMILE) Hey Lefty, I thought we would be hearing from you after Bug mentioned LUCAS. Have a Happy Labor Day to all the Pinto...
... finding a gasket, and dumping in ten quarts of some 'get me by ATF'. Quite simply used the highest quality ATF made, full synthetic from Amsoil, and...
hello does a new fuel pump come with the spacer ??/mine is samage does anyone know where I can find one?? Thank you frank. __________________________________...
hello does a new fuel pump come with the spacer ??/mine is samage does anyone know where I can find one?? Thank you frank. _______________________________ Do...
I've never gotten a spacer with a fuel pump. You can get a shorter fuel pump pushrod to use with a gasket only if it's the 2.0 that your talking about. George...
escofam@...
Sep 7, 2004 11:37 pm
18614
I think you've got the wrong person or tell me what was posted. ... [Non-text portions of this message have been removed]...
No gasket is required. The cooler lines going to the radiator can be disconnected, slip a rubber hose over the end of the tubing, then guide it to a large...
ATF fluids are not all the same. Many "types" exist. The idea of putting in new fluid, at pre-determined intervals, is to extend life of the trans, provided...
