To the folks still on this group, I haven't been active on it for some time now, but, because of the high level of spam, posts by new members require approval....
There is a lot of activity elsewhere about the DIS and INPA interfaces, with people successfully diagnosing their BMW's. Questions to the group. 1. Who has DIS...
Hi All, My OBD2 ISO ELM323 interface and WGIobd11 software type does not read the ABS or Airbag light MIL on the instrument panel on my 2000 Z3. The software...
Hi, sorry i have not been able to reply to people really busy with school and work. All the files and instructions are available on emule. just search for bmw...
Hello, Any no how to swap the com2 as com1 on SCO unix(runned DIS V29)? My notebook phsical equipped with 1 com port(com A) and 1 infrad (com B), but I need...
I'm experimenting with a passthru device (not Actia or Snap-On) on bmwtechinfo.com, and I'm running into some bus problems. BMW is not helpful; they say buy...
Am trying to change my sparkplugs and am debating hwther to get the NGK BKR6EQUP which are the original equipment and are platinum, or to get NGK BKR6E which...
Hello, Has anyone installed anything other than version39 DIS on laptop? I want to install version 44 GT1 on a laptop.. can I do this??? Also has anyone...
Hi, can someone how followed the shoulders instructions and succeeded, tell us the exact hardware configuration he tried it on? What Laptop, processor,...
Hello v39 users, I have v39 running based on shoulders very good description. Thank you! I am using vmware and assigned a different IP address than the default...
Finally I have a working DIS v29 with V28 program on vmware. However I cannot make contact with the head. Can anybody tell me what COM port the Modic III head...
******************* Do not pay for DIS / GT1 install. ************************* Instructions are in the files area (not complete with files). Tested and ...
Hi, I've searched the net and found out quite a bit about the I-bus. I've read a few BMW papers, and one stated that the I-bus is present on the E31-series....
So, after getting the GT1 V39 and other stuff installed, where does one go to buy the hardware/cables/connectors so that my PC can be connected to the car?...
Hi All, I just tradein my X5 for 740, and I have no navigation unit. I wanted to know where is the OBC is located and if it is possible to upgrade the...
Here's a first look at the circuit board for my I-Bus/video/mp3 module project: http://autos.groups.yahoo.com/group/openbmw/files/Multimedia_Module_Project/ ...
I purchased a Digimoto (http://www.digimoto.com/) ELMscan box/cable setup (not the latest version they're selling on their site -- mine is OBDII to DB9 on the...
Hi All, Other than my GT1 and DIS software exploits I have done a car PC install that has an OBDII interphase (BMW said it was not compatable). Would anyone be...
Hi Anyone tried to read and being able to get the wiring diagrams and other info out of the BMW DIS SW CD's? It apears to be a Linux/UNIX system! Thoose images...
Dear ALL At last I made BMW gt1 on normal pc it is TESTED & WORKING. I tryed it on diagnostic head and opps direct and through network. Fare well original GT1....
Currently have a VDO system fitted but don't like the position of where the screen sits in front of the gear knob. So thinking of getting a BMW 16:9 monitor. ...
HI All, When i try an activate a TIS CD in DIS I get the error "the disk in cd drive 1 could not be activated. fault -46" Any Ideas, I have had a german one...
Car is a 1998 E39. I have a problem with the windscreen wipers running all the time, even with the ignition off, and also the headlight and intensive cleaner...
After browsed this board, I got the knowledge about the GT1 and SSS, but I can't sure if I correct, any correction is welcome. 1. The GT1 with DH work full...