Nick, 1. I have a hard time keeping the oil pressure up at a stop light. Going into first is a pain. Really slow...but still, I ain't racing the thing. My...
Jim, I was told the trans was out of a '64. All I know for sure is the 9 inch rear end and trans were out of the same truck. It is not the small trans. The...
Don,,, behind on Emails,,,, LOL,,, besides mine, lately over 50 of em,,, wearinging me out,, anyway,, Just wanted to Thank You and everyone else for the help,...
Jim,, Have suspected possible same transmission to bellhousing bolt pattern for the two trannys??? Not uncommon for Ford to use the same case and change the...
Marv,, as I know it??? There was a H/D option available for the 64, it used the small six, with the 9” rear axle,, the driveshaft being the rare bare. If...
Nick,,, sounds like a lot of probs to sort out,,,, when you say going into first a pain,,, wondering why?? There is an adjustment setup for the manuals and...
I have had 2 windshield's replaced in the last 9 months. The 1st cost $150.00 installed & the 2nd one installed last week cost $180.00. PRICE OF GAS WENT UP. ...
Vic, I just checked the transmission numbers and it is a C-5 XXXX. Then, if I all this understand correctly, and IF the flywheel is too close (???) to the...
At a good hardware store you can find a paint spray system based on a refillable sparyer and a removeable aerosol charge. About the same size as a Rattle...
Vic and Marv, It's also not unheard of to have a late '64 that would use the parts for '65 model year ! Also many vehicles are titled in the year first sold in...
Marv, Is the U-joint at the trans end of the drive shaft a small ( internal clip ) or a large ( external clip ) ? '64 is the first year to offer the 9" rear as...
Marv, What king of transmission mount do you have ? '64 would have the round donut for the 61-64. '65-67 has a square mount. Jim in GA / Blue Lemon ...
I had no idea that my simple little question would start such a debate! I don't know if I've learned a lot ...or if I'm more confused! Either way, I'm taking...
FYI, that is what's called a "PREVAL" brand spray system. Another cheap alternative is in the Wal-Mart model cars. they have mini paint guns for spraying...
Seems to happen all the time,, the good thing is some real important answers,, myself now learning two different styles of the 240 member , the first advice...
Air gun,, touch up for $29 bucks works SUPER,, however back to the two part paint,,, impossible as I know it to get the same hardness with out a hardener...
Chet, I had to replace the windshied in one of my 61 pickups. The windshield was'nt as bad as the gasket. The other was a van i have had for 20 years & just...
Look on line, some windshield places will give you a quote. The best i got was $214.00 on line. My windshields are PPG Tinted. jerry in az. Victor La...
That is the same windshield that I have too. I like PPG. Got one of theirs in my Ranger too. Will do the same for F250. Thanks William in AR ... From: Jerry...
wait... there's a 200 crossmember?! You mean from a truck, not an Econo, right? Joe Chicago ... member , ... well as ... to ... forum ... to ... swap ... ...
Vic, My PU is a '62 that had a small 6. I changed to the 9 in. rear end several years ago and kept the small trans. Now I have a 302, a C-5 xxxx trans. with...
Jim, The U-joint at the trans. end has an external clip but I have no way of knowing if it is large or small. At the rear end of the shaft the clips are ...
Jim, The trans. mount is the donut type. The numbers on the case are C-5-xxxx Marv in WI ... From: Jim Bulger To: oldeconolines@yahoogroups.com Sent: Monday,...
According to Don's informative 101 newsletter, the 9" became an option in '63. Mark in WV Is the U-joint at the trans end of the drive shaft a small ( internal...
