Doug, i have a ke16 that im wrecking. it got hit in the rear on the drivers side so the passenger side hinge might still be ok. ill take a look tonight, it...
HI I've been a member for a while but haven't posted cause the AE-70 project wasn't going anywhere. I have been offered a 2TGEU engine by a bloke who has one...
i'd expect 5 or 6 hundred AU. you pick a 5k up for about 3-4 hundred these days, and a 3tgteu is only worth about 12 hundred from the wreckers (read: inflated...
hey guys trying desperately to place ke70 5 speed into my ke16 the only problem ive found is the crossmember has not a chance of fitting ke16 is no good...
No only standard springs but if any one is after a front or rear end or 4ac from a Ae71 just email me at bplattens@... no gearbox tho as thats going in...
Yes I had this problem with my KE18 I just made a new Xmember Philip ... _________________________________________________________________ Sell your car for $9...
Philip Bryant
levinte27@...
Jun 2, 2005 9:28 pm
22510
yep i got an rt142. all up its cost me slightly under $500 for the car and fixing it up to pass a blueslip. thats not bad :) this is my first experience with...
... fitting ... the ... if that is the 4k engine with the 5 speed transmission i think that what my mechanic did was to modify the hump where the transmission...
hey guys heres a link for some ke parts check this out http://www.buyandsellph.com/ just check out the car parts section.today they have a bumper for a ke 15...
... option ... parts ... well mine had an aircon plus a heater and it was all stock direct from the factory the aircon was a nippondenso but unfortunately i...
i have a ke70 5 speed in both my ke15 and ke16. i just drilled 2 holes in the original xmember and everything simply bolted up. one of the holes is on a bit of...
Hey all, I am needing help from any of the wrecker hounds out there, I am chasing a 4" wide Toyota rim with the 114.3 x 4 (ke30) stud pattern? Preferably a...
Sorry, forgot to mention must be 14" rims Scott ... From: oldcorollas@yahoogroups.com [mailto:oldcorollas@yahoogroups.com] On Behalf Of Scott Hoffman Sent:...
... pretty sure all the early corona/celica rims were 5" or 5.5". you might also want to look at van rims that aren't 5 stud, maybe hiace or nissan vanette or...
... and if you want skinny front runners for your 13b turbo ke20 when you pilot it down willowbank drag strip, that's perfectly fine. he asked where to get...
Yeah a mate has just finished changing the offset on some 14" x 7" RA40 celica rims I scored. (I fluked these, they are stamped ROH so must be custom) a 24.5 x...
... *smacks forehead* my daily driver is a 96 econovan, 1.8 petrol, but not dual tyres. it comes with 14x4.5 wheels and i'm pretty sure they're ke30 stud...
Cheers, would be good, what does the rim look like? Hopefully I can still fit the chrome outer dress rim and maybe weld on a sleeve for the centre cap to push...
Sorry for the slow reply Phillip, I've been offline for a bit. The struts were just generic ones that I purchased at Repco, listed as replacement ones for...
Seriously thinking about getting cam ground as I'm going to replace the head gasket. Has anyone recently got a cam ground, Price? I remeber a wade 169 was a...
Great Work! What you said about the SU carbs is so right. I tried a set of 1 1/2" Datsun SUs with a Lynx manifold on the old, mildly worked 5k in my race car....
... having learnt how SUs work, i'd confidently say the last 120-odd years of development with venturis and jets and emulsion tubes have been a total waste of...
The new 5k I've built but not installed yet may be a dirrerent story, I'll see when I finally get it in. Its much more highly developed than the engine I tried...
Ah, Hitachi SU's! It's been a while since I've played with them. Another good thing to do is get them modified to fit english SU needles. Hitachi needles...
Righto this is shit, I'm in Townsville, didn't think it was that backwards, but IT IS. Repco is the only place in town with a cam grinder, and they don't do...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
