No ; $pend your money towards reducing the engine's RPM's instead by fitting tall narrow tires like it was designed for and consider the 3.55 final drive...
Grey for the _entire_ engine and all the accessories were painted gloss black , not the satin black most " restorers " use ~ for those who don't know and wish...
It is a sintered bronze bushing . Most of the time you can work a long prybar up in there and work the tranny loose if you're young & strong , you'll need a...
Be careful ! . Mark here has the parts you need but he kippered off with my $ and never said sorry nor why.... didn't send me anything so I'd suggest a C.O.D....
I don't know but the reason has to be dead simple ~ look down inside the new balancer and measure it with some calipers to see if it's got a step or isn't as...
What I did was stick all my largest screwdrivers in there between the trans and bell housing, then rocked the heck out of the trans. Then take up the slack and...
Are you replacing the oil seal there? Some suggest keeping the front cover loose until you've installed the balancer to allow the seal to center on the ...
Nate, I have been trying to locate your proceedure to clean out my cooling system with citric acid but have been unable to find it. I have been searching old...
I am working on the brakes on my '52 3100 and have run up against a problem. There is a special bolt on the back of my master cylinder that holds a brass block...
The current on-line Heavy Chevy catalog shows them, still at $5.00 About 1/2 way down this page, item # 245 http://www.heavychevy.com/html/brakes.html ...
Tom ; Go tohomepage and search all my posts from there . if that doesn;t work I'll have to sit down and write it up again . Or maybe one of the nice people...
Yes, look for Nate's email from last fall with a key word "solder bloom". That should do it. Here are the cliff notes: This assumes the rad is out of the...
Hi john, i'm in minnesota, ... From: John <scowdin@...> Subject: Re: [old-chevy-truck] '48 Loadmaster To: old-chevy-truck@yahoogroups.com Date: Sunday,...
Hello gang! Now that I have located a set of running boards for my wife's '48 short bed, I need to come up with a pair of brackets/braces to support them. I...
... From: vwnate1 <vwnate1@...> To: old-chevy-truck@yahoogroups.com Sent: Fri, 29 Feb 2008 11:00 am Subject: [old-chevy-truck] Re: On the road Again Good...
think i posted it it was on feb 29 John Jef city MO 52 3/4 ton chevy ... From: vwnate1 <vwnate1@...> To: old-chevy-truck@yahoogroups.com Sent: Wed, 2 Jul...
Here is a 47 on eBay for sale. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&sspagename=ADME% 3AB%3ASS%3AUS%3A1123&viewitem=&item=120279151214 ...
Hey Rob. I do have lots of extra parts Hoods fenders grills, Been saveing lots of good parts and trucks for future restrations. Never thought much about...
John
scowdin@...
Jul 3, 2008 1:02 am
37798
... From: vwnate1 To: old-chevy-truck@yahoogroups.com Sent: Wednesday, June 13, 2007 10:24 AM Subject: [old-chevy-truck] Re: Trouble Shooting Overheating Allen...
Allen ; That was someone else's response to my original post as I never take the radiator out , in fact I drive the vehicle daily whilst I'm cleaning it as...
Don't _ever_ run without a thermostat , it's very bad for the engine as the coolant circulates too rapidly to pick up heat so the engine is hotter that the...
Yup , you did , I just re-posted it under " Citric Acid " with grammar and spelling corrections (I hope) so all can find it later . maybe it should go in the '...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
