... took all ... went on the ... the key on ... should.I do have a ... there ... Another ?,Nate had ... being ... it's still a ... Hope its a 6 volt battery in...
My 47 1 ton has a power take off system. I had never really looked at it before, since I did not know how it worked until I tried the winch that is on it. It...
I haven't seen one of these cabs yet, but I think it is good for the hobby to have the extra option of just replacing the entire cab as a unit. Hopefully they...
I'm not an expert on every combination of PTO's and implements out there but if yours is powering a winch then chances are that you will have a reversible PTO...
Jeff, Right on. Most can at least bolt things together to save money. If not inclined to do their own body work, at least this gives another option to keep the...
They were only fitted to the larger trucks so look in that rusted out Bobtail , van or milk truck in the corner of the scrapyard.... They're not good engine...
Follow my posted testing procedure , no skipping steps and in the correct order , you'll know just what it neds in 15 minutes , no guessing , wa$ted Time nor $...
Cool ! we didn't want you to get any tickets for blowing red lights or worse . Remember : the pedal may go down in a few hundred miles so re-adjust as needed ,...
I didn't realize these were _NEW_ trucks , I thought they were high dollar rebuilds . I don't want a new truck no matterhow different it looks . Throphies ~...
So then , we can extropolate you have a Muncie SM420 tranny ? the PTO hangs off the left (driver's) side of the tranny does it ? . For a winch it should have a...
In my area all the salvage yards have gotten rid of the old stuff when steel prices went up. They were also in other trucks but they are hard to find. Took a...
The Southern Trucks are totally new with 3 yr/36k warranty. Extra space in cab, chopped top. Go to their web page, also on news stand now "Custom Trucks"...
Excellent advice, Nate...as always. One thing I did find when adjusting the brakes...the right front one was a little too tight, and the wheel wasn't turning...
In a message dated 11/1/2006 8:35:21 A.M. Central Standard Time, vwnate1@... writes: They were only fitted to the larger trucks so look in that rusted...
For Nate and Jeff, Yes the PTO hangs off the left side of the trans. The PTO does lazily turn in what appears to be neutral. You must depress the clutch in...
The GMC 55-59 shop manual has a bunch of PTO info. If you can figure out what model you have I'll check my manual and see if it is in there. PTOs are not...
It's made by Tulsa Power Take-Off (which apparently no longer exists). I posted new pictures on the web photo page (since apparently you cannot attach them...
The following is a website I came across a while back of a company called USBody that produces reproduction fiberglass cabs, beds, doors, etc. They have heavy...
I have a rusted out left front fender that I want to replace with a solid unit. I have all the bolts out but can't figure out how to remove the fender. Do I...
Hi all. On subject of high torque 292. My dad's 1964 C-10 pick-up came with a 292 from factory. Its a long bed with overload springs. The dealer marketed...
I will pipe in here although I don't have a 1951 here to look at. Double check that all the fender bolts are out. You may want to wire brush around the inside...
Virgil, Yes, I have looked at half tons on up. Measure again, I think you can put the 292 in a 53. You may have to modify front shroud to move radiator...
Good thoughts Walt. I figured moving radiator and some firewall work would be in order. Guess my heart wasn't really in it. It was one of those thoughts...
I am building a 250 for now. It will do OK for a driver to get milage and dependable. No hi performance needed on it. I will use it to play with fuel injection...
BW, On my 49, there are at least 2 screws from the top of the grill, under the top bar.. You will probably have to pull the parking light to get them. Then...
I really appreciate your time Steve.It is in fact a real 6vlt. battery.I looked at the diagram in my manual and it appears as though the sending unit is ...
Wu5clan@...
Nov 2, 2006 2:18 am
32766
Thanks Nate.Made the mistake of deleting your post.If you read my last post and think I'm off track,could you please repost your instructions.Thanks.Tom in...
Wu5clan@...
Nov 2, 2006 2:21 am
32767
I could be wrong here,but aren't there some bolts inside the cab on or near the floor board that attach to the fender as well?Or are they just for the inner...
Wu5clan@...
Nov 2, 2006 2:25 am
32768
Thanks for checking. "Hanlon, Bill (ISS Houston)" <Bill.Hanlon@...> wrote: I was wrong (not the first time today). The TF GMC manual only covers ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
