I have looked at a lot of these old trucks and also had grounding issues. What I found was that some trucks have a ground wire from the mountying plate and...
To answer your question about a frame around the glass itself, no, none of the windows that went in doors WITH vent wings had frames around them; only non-vent...
Nate, thanks very much for all the info. I did check the gauge by taking the wire loose from the back of it. It immediately moved to 'full'. So I think the...
Tom Did you touch the sender wire to ground at the tank to see if the gauge went to full? I think I would be temped to replace the lamp cord wire and run a new...
Lee, I have checked the gauge by taking the wire off the back of it. Gauge goes all the way to full very quickly, so the gauge seems to be fine. You make a...
Check out Deves website he even gave the part # front and back. 52 3100 DELUXE CAB 51 3/4 flatbed 70 CST Wichita Ks John ... From: "Dennis Miga"...
John & Sherry
scowdin@...
Jan 2, 2006 1:27 am
29642
I picked up a used set of 265-75-15 on 15x8 rims. They fit under my rear fenders with about a finger of clearance, but have plenty of room on the front of my...
Hi im selling my 1949 chevy 3600 2wd cheap, it has a inline 6 engine manual shift, frame is great body does have some rusted/cut away peices, has the hood for...
Hello all, I have a 1949 3100 with a 1955 235 engine. The starter recently gave out and I need to remove it. The nuts are stuck. Another problem I'm having is...
Gee I thought sure this was gonna be one of them pretty good spams....... ... Ole Chevy and GMC trucks rule! To unsubscribe, send an email (with no subject, no...
I'd say use a 6 point wrench. 18mm perhaps The top nut and bottom ......one is fine threaded nut on a stud, the other bolts in. Don't remember which is...
what is the differential geared at? ... I need a seat. mine has springs broken down by previous owner Ole Chevy and GMC trucks rule! To unsubscribe, send an...
For those who follow BillyBob's progress, a new Work-in-Progress log entry "Makeup Makeover" has been posted. During the body phase of BillyBob's detailing...
Larry R. Kephart
vpa@...
Jan 3, 2006 10:06 pm
29652
Hey guys, I am looking for some pictures of the original rims for a 57 3100. I have been browsing the sites (Brothers, Palmer, etc, etc) but have seen a few...
Scott Mountney
scott@...
Jan 4, 2006 7:19 am
29653
Keep at it and let us know , my gauge moved the other day so I went to fill it up , it had been at 1/3 tank and it took 9 gallons (about 1/2 a tank) , the...
You can eather clean off the tops , remove the filler scews and top then up with Glycerin or shock fluid ($!) or tractor oil or go buy a nifty set of tube...
Pete: I did this with my 17" rims. I blasted the two large pieces and had them powdercoated. I inspected the lockrings and concluded that they were best left...
Nate, From what I've learned recently about these systems suggests that you have a 90 ohm sender which was made for the "later" gauges, versus a 30 ohm sender ...
Larry, that's probably the best looking "farmer" paint job I've seen, the prep work you are doing is what makes any paint job. Good to hear from you. Lee ...
Well, after trying everything, I finally checked out the sender unit and found that it's bad. Need to get a new one. Where's the best place to order one??...
Tom, it was me that got one from Carter's. It has been working fine for some time. I am sure you could get one from Chevy Duty or American Classic Truck, or...
Up date on Lights. First of all if nothing else works check out the ground connection, make sure that it is grounded all the way to the fuse panel. Then maybe...
Sounds good -but- the sender is a N.O.S. one I installed recently , yes I checked the part # before I bought it off E-pay and it worked O.K. for a month or two...
Thanks for the info on the sender, Roy. I'll check Carter's and the other vendors. Should be able to find one easily. I sure appreciate all your help! Tom...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
