... As far as I know, yes. But it's been slow since I've been on. You might also want to try Neons.org if you want more info. Good luck. ===== Scott ...
Moparilus on MSN Groups is a place where fans and owners of modern Chrysler's, Dodge's, or Jeep's can discuss and chat about their vehicles and their...
Dyno results from my R/T can be seen at www.aempower.com 125hp baseline 130hp after CAI 6.4hp peak at 5500rpm 115ft of tq baseline 120ft of tq after CAI 6.1ft...
im looking to use 10.5 compression pistions, im boring the block out 20ths and want to deck the head and the block, what does anybody suggest for the amount i...
The limit for the amount you take off the block deck is determined by how much piston to head clearance you have. I would only deck enough to ensure that it...
I think I'm not launching with enough RPM. I should have ran 15.8 or so last night, but I never launched higher than about 3000rpm and maybe have dropped below...
Hi, finally got a chance to run the acr after i rebuilt the engine. these times are on nitto 450 tires(which suck) times are as follows 60- 2.224 330- 6.116...
Yeah I kinda agree about the Kumhos. If I launch about 3500rpm I will end up spinning all the way thru first. But then again I was getting 2.1-2.2's, and an...
Yeah maybe I need more runs on them. But there not the tires I wanted anyway, and drags only cost about $12-15 more each. I want 2.2's wherever I go and drags...
A long tube header like the A/Fx or Blackdog will go along way, so would a DOHC PCM or A/FX Race PCM for additional flexibility. What I would really do if I...
in my title it should read car not acr. anyway ive been running back and forth with jeff b, and he is still ahead. mods are as follows afx race ecu,afx udp,...
Those times aren't bad for the mods you have and your about the only person that is running the Crane #14 with high compression. All your missing is a better...
well right now im running 93 octane from mobil. its pings slightly at light throttle untill it pulls timing, then i have to pull 4* more with the msd box. that...
Hawk brake pads at deep discounts! We carry the full line of Hawk Pads - HPS, HP Plus, Blue 9012, HT10, HT12, HT14, HT15, MT4 and SuperDuty. High performance...
Hawk brake pads at deep discounts! We carry the full line of Hawk Pads - HPS, HP Plus, Blue 9012, HT10, HT12, HT14, HT15, MT4 and SuperDuty. High performance...
hi there, i just got my 02' neon 1 month ago. check my website and let me knwo what you think of it. i've a few questions. could i use 1st gen stock springs to...
... My understanding is, no. if so, how much lower ... I would stay away from lowering the car more than an inch, unless you decide to go with coilovers. The...
OEM 1st gen ACR/RT springs do fit and lower the car about 1.5 all around. They don't effect the stock struts that much, because the spring rate isn't much...
... The spring rates on 1st gen ACRs are higher than the 2nd gens? That doesn't make much sense, as the 2gen cars are heavier. ... Do you have proof that MP...
The spring rates on both 1st and 2nd gen R/T are the same. The new cars have an 1" more of suspension travel, they used taller springs to get it. Yes I have...
So as summer offically is coming to a close, this fall and winter looks like it should be pretty exciting for Neon-lovers everywhere. The upcoming SRT-4 is...
... OK, I won't argue that the 2nd gen suspenion has more travel, since 2nd gen cars seem to be leaping to the sky. But spring height has nothing to do with...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
