Head...manifold....i'm still waiting. If I ever get some BD parts, I'll be so overjoyed that I'll post. ... From: dink_2_2 [mailto:dink_2_2@...] Sent:...
Yup.. in one fell swoop, all of the SOHC owners of the world has been wiped away. We're all now driving BMW M5s and AMG S55s as reward for our many years of...
Hey you coming to carlisle this weekend. Haven't seen you in awhile hope to see you there any races you going to this year? Lee Sebring P.S. we did squeeze a...
... If I get to pick up my new truck I will be there entered in the stock class for Dodge Rams. Hope to go racing in a few weeks have to get new motor in and...
Lee, haven't heard from you or cliff in a while. How you guys doing. You aren't running a 13 on an all motor SOHC are you. That must be with juice. I've...
... As far as I know, yes. But it's been slow since I've been on. You might also want to try Neons.org if you want more info. Good luck. ===== Scott ...
Moparilus on MSN Groups is a place where fans and owners of modern Chrysler's, Dodge's, or Jeep's can discuss and chat about their vehicles and their...
Dyno results from my R/T can be seen at www.aempower.com 125hp baseline 130hp after CAI 6.4hp peak at 5500rpm 115ft of tq baseline 120ft of tq after CAI 6.1ft...
im looking to use 10.5 compression pistions, im boring the block out 20ths and want to deck the head and the block, what does anybody suggest for the amount i...
The limit for the amount you take off the block deck is determined by how much piston to head clearance you have. I would only deck enough to ensure that it...
I think I'm not launching with enough RPM. I should have ran 15.8 or so last night, but I never launched higher than about 3000rpm and maybe have dropped below...
Hi, finally got a chance to run the acr after i rebuilt the engine. these times are on nitto 450 tires(which suck) times are as follows 60- 2.224 330- 6.116...
Yeah I kinda agree about the Kumhos. If I launch about 3500rpm I will end up spinning all the way thru first. But then again I was getting 2.1-2.2's, and an...
Yeah maybe I need more runs on them. But there not the tires I wanted anyway, and drags only cost about $12-15 more each. I want 2.2's wherever I go and drags...
A long tube header like the A/Fx or Blackdog will go along way, so would a DOHC PCM or A/FX Race PCM for additional flexibility. What I would really do if I...
in my title it should read car not acr. anyway ive been running back and forth with jeff b, and he is still ahead. mods are as follows afx race ecu,afx udp,...
Those times aren't bad for the mods you have and your about the only person that is running the Crane #14 with high compression. All your missing is a better...
well right now im running 93 octane from mobil. its pings slightly at light throttle untill it pulls timing, then i have to pull 4* more with the msd box. that...
Hawk brake pads at deep discounts! We carry the full line of Hawk Pads - HPS, HP Plus, Blue 9012, HT10, HT12, HT14, HT15, MT4 and SuperDuty. High performance...
Hawk brake pads at deep discounts! We carry the full line of Hawk Pads - HPS, HP Plus, Blue 9012, HT10, HT12, HT14, HT15, MT4 and SuperDuty. High performance...
hi there, i just got my 02' neon 1 month ago. check my website and let me knwo what you think of it. i've a few questions. could i use 1st gen stock springs to...
... My understanding is, no. if so, how much lower ... I would stay away from lowering the car more than an inch, unless you decide to go with coilovers. The...
OEM 1st gen ACR/RT springs do fit and lower the car about 1.5 all around. They don't effect the stock struts that much, because the spring rate isn't much...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
