Does anyone know what the correct fuel pressure to the carburetor should be? I wanted to make sure I have the proper fuel pressure from the fuel pump to the...
hello the pump pressure must be 1.0 idle to 1.2 on high revs greetings george ... From: Stephen Sebastian To: muttmotorpool@yahoogroups.com Sent: Thursday,...
Thank You very much! I was guessing that it was between 3-7lbs, but this nails it exactly! Stephen ... I believe it says 4.9 to 5.4 psi at the carburetor....
My guess is that it would be the same regardless of the type of fuel pump since fuel pressure requirements are determined by the carb and in particular the...
hi joe yes it is also the same type carburator george ... From: Joe Kaiser To: muttmotorpool@yahoogroups.com Sent: Thursday, July 05, 2007 3:21 PM Subject: Re:...
Well all I finally have been able to get over to the computers again, with some time to thank all of you that have sent those wonderful boxes of joy! We all...
I have an A2 engine and Transmission that are taking too much room in the garage. I built a few years ago and haven't had the need to use. I ran the block in...
don't know the tech answer but 5-7 lbs is the standard for most fuel systems (carburated) ... _________________________________________________________________...
Good Luck I can't sell two good take outs for $100 each! crosbymech <crosbymech@...> wrote: I have an A2 engine and Transmission that are taking too much...
Here it is a year later. But I had promised to share how this persistent problem of carburetor flooding was finally resolved. I had followed up on all the...
If you weren't so far from the center of the universe (Centralia WA) I would have picked up those takeouts when you posted them. Mutt stuff is hard to find out...
Center of the univers in WA?....:) Shipping can be arranged.... :) Everett Cole <militaryjeeper@...> wrote: If you weren't so far from the center of...
I was emailing someonea about a couple of power packs but comp died. Was that you ? YOu moving?? ... (Centralia WA) I would ... hard to ... at Fort ... ...
Well, the center of my little world anyway. Why do you think they call it Centralia. ... _________________________________________________________________ ...
I own a 1971 Mutt M-151 A2. It runs smoothly and everything works fine. I own as well a Suzuki Samurai. I´ll be posting some photos soon. I´m interested in...
Sarge Mark I live in Aguascalientes (central Mexico), and both my Mutt and Samurai are here at my house. I have ways of moving them to the border or so. The...
Clearance should be 0.015" cold. A handy tip is to set No. 8 valve (back of engine) with No 1 fully opened, No. 7 with No. 2 fully opened, No. 6 with No. 3...
I thought is was .015" warm and I know the manual says to adjust the valves while the motor is warm and running. I always wear my oldest cloths and safety...
Mutt enthusiast looking for a good Mutt project here in the Mid West /Chicaoland area. Have some cash, some interesting scooters and a 1964 Chevy Nova to offer...
Wow, It has been quite some time since I have been on here with connectivity and time to give you all an update as to what is happening around here. But first...
On this side of the world it was reported that 4 people were killed by celebratory(friendly) fire after the big win. Never saw that happen after a seahawks...
Hey how are you. I did not know you were in Iraq, and I just wanted to ask you if you knew a cousin of mine, his name is Sgt. Matthew Joseph Munden. And I also...
my A2 has to go to make room for new prodject. I restored it about 4 years ago. I have enjoyed how extremely rugged it is and I hate to do it but its gota go....
That MUTT should sell in a heartbeat. Also try listing it in http://www.g503.com/forums/ cause there are a lot of hungry MUTTers there. Best of luck. Ron M ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
