Can anything be done to eliminate the noise of a M151A2? During winter I have the hard top on and it works like a "speaker", so the noise is a lot. In the city...
Remember the old style has small wings to tighten down that tend to snap off. New style solved that problem. "Stu" Southern New Hampshire, USA "Live Free Or...
Get rid of the hard top? "Stu" Southern New Hampshire, USA "Live Free Or Die" shootingstuff4free.com MVPA #14790 1967 M151A1 Jeep 1964 M416 Trailer 1986...
In Germany I always wore earmuff style hearing protectors on the Autobahn. On my M-718 (151 series, frontline ambulance) I added thick rubber cut from loading...
I can't recall the company name, but there is a source of sound deadening material that you can glue to the inside of the hard top and elsewhere to absorb a...
You might want to try DYNAMAT I know the hot-rodders use it. dynamat.com ... __________________________________ Do you Yahoo!? Yahoo! Mail - You care about...
Yes, that's the stuff I was trying to remember. Thanks, Scott, Dick ... From: Scott Christ To: muttmotorpool@yahoogroups.com Cc: Muttmod@yahoogroups.com Sent:...
Dick and list, its called "DynoMat" or something close to that spelling, check your local stereo shop, its pricey, but you get what you pay for.......I would...
Thanks, Cliff: Do you know what the matting material is in the HMMWV? I'm thinking of a hard top for my A2 MUTT and am aware of the noise issue. Watch your 6,...
Dick and listers, If you have a HMMWV near you check one out, you will see the matting ALL over the vehicle. Its closed cell foam (1/2" or so) with a vinyl top...
I have two complete motors that I will be glad to work a good deal on, contact me at top.marinesmc@... located in WA state ... anyone ... last ... was ...
Hey guys my m151 has a foam matting insulation all over the inside of the body and cab. it seems to help with the noise but it was a real mess i did not put...
Good day to all, Would anyone know if there is an after market set of intake gaskets available, or is there suitable substitute until I can get an nos set to...
Question: After you replaced batteries, did you operate your vehicle on the highway for sometime? If so, perhaps your generator stopped charging and you were...
guys, i need guidance-the brake lights on my 151a2 quit working, i replaced the bulbs, and still nothing. my question is where should i start trouble shooting?...
Richard, First check to see if your B.O. stop light is working, that'll clear the stop light switch. Second, check that your headlight switch is in the correct...
Best starting points are the fuse and brake light switch. Dick ... From: eslava46 To: muttmotorpool@yahoogroups.com Sent: 03 February, 2005 09:51 Subject:...
Thanx for your immediate answers for once more I'll try what I can and get back to you. Oh and about that heater problems that I had, the guy that restored my...
But a Wrangler doesn't look nearly as cool as a MUTT. :) Dick ... From: gr_m151a2 To: muttmotorpool@yahoogroups.com Sent: 03 February, 2005 23:34 Subject: Re:...
"Ya don't throw the baby out with the dirty bath water" Stu Ellis RealtorR Century21 Cooper & Associates, Inc. Phone: (603) 845-0876 Cell: (603) 548-3901 ...
Hello all, I have to replace the rubber brake hoses, wheel cylinders, and brake shoes front and rear. I am seeking civilian cross reference part numbers....
Has anyone bought one of those Carolina Growlers? I was thinking of purchasing one of the kits for $7500.,and wanted a hard top for it. Which I could have...
Can you latch onto a borescope? You might have a carbon bridge in the cylinder that's effectively shorting out the high voltage. The plug smells of fuel, so...
hoy DICK the only thing thad you can try thad i know is let the engine run take a sprycan of brakeclean spry it on the intake manifold near /on the gaskits if...
Hello from Atlanta GA 30306. I am having difficulty getting to the rear lower alternator bolt to loosen it to adjust the belt tension. Any tricks to this...
