Both are available from the importer, Herm Baver at Herdan Motors. www.hermys.com or www.herdan.com . Herm is not great about answering email, but he is...
Hi I'm rebuilding the top end of my morini 350 and stupidly forgot to ask NLM for the torque settings for the head studs when I bought the parts. If anyone...
Hi I'm rebuilding the top end of my morini 350 and stupidly forgot to ask NLM for the torque settings for the head studs when I bought the parts. If anyone...
Hello from Minnetonka, Mn i am nearing completion on a 1985 k2, i need the following rear brake pedal and actuator, new or usable throttle grips, new or nicely...
Hello from Minnetonka, Mn i am nearing completion on a 1985 k2, i need the following rear brake pedal and actuator, new or usable throttle grips, new or nicely...
Herm is really old and kinda frail, and Herm Jr. is not up on Morini's nearly as much. NLM are expensive (esp. bc of the exchange rate), but they probably have...
Does the K2 use the standard Italian CEV design tailight? The lens (repro's) are available on eBay for cheap (9.99 plus shipping). Screws are available at the...
I have an almost running Morini 500S for sale for a lot less than I paid for it ($1,500). I live in Washington State for viewing/pick-up or if you REALLY want...
The bottom red warning lamp on the centre between the clocks on a 1981 500 Camel. What are the letters below as mine are worn off and what does the warning...
hi all - eric webster has advised me of this; if you look back on records i set up the group several yrs ago but have not been very proactive with it,...
Hello all, I'm a Morini admirer who recently set up a website that's not technical, instead it's rather about the fabulous looks of Moto Morinis. Have a look...
Hi everyone, I don't own a Morini yet, but I went on a test ride on a Strada K2 the other day. It had an aftermarket 2 into 1 exhaust and was astonishingly...
Hi - I'd say that my 350 sport is a lot smoother than my 650 Triumph, but rougher than my 600 Monster (or my Dad's Guzzi V50 for that matter). It's certainly...
My morinis' have all been relatively smooth running, all the better so when the carbs have been balanced. A little tingling/buzzing through the footpegs would...
It's been a year since I joined this group after getting some advice on a 500s for sale. We have since bought the bike but it has sat collecting dust until...
Lance It is pretty tough to give any counsel on how you may get those Mikuni's working. Have you checked to see that they are complete, clean, and jetted for...
... Having kicked it over for a while are the pkugs wet or smelling of fuel? What sort of Mikuni are they? Regular round slide carbs? It might still be the...
Usually with the morini's if your getting a spark then the electrics are ok. The timing doesn't usually slip. The common problems are the pick up cracking or...
Wow, thanks for all of the replies. I did go through every motion mentioned and finally decided to put the battery back on the trickle charger overnight. It...
hmm, not sure about that one. Did it run properly before the lay up with those mikuni carbs? Are they jetted up correctly on the pilot jets etc. Morini's are...
I honestly can't think of anything other than the carbs that could be causing the problem. So tonight I'll pull them off and check the jetting and look for...
Howdy, my name is Dave,I live in fresno, Cali. i bought a 1987 moto morini camel 501 x3 last june (posted pics in the photo albums)and have found it hard to...
Hi guys, Anyone have any suggestions as to where to look for a gas tank, decals, stock paint for the tank. And, I need a front wheel. Any help would be...
I think you can try from MOTORICAMBI MORO in VARESE (italy) you can ask him via e-mail Marc Bennett <maha.vir@...> ha scritto: Hi guys, Anyone have any...
Hi, my name is Peg and I have purchased my second Moto Morini 500. She is only 50 numbers off my first one so it was a no-brainer to buy it. I am so...
I would suggest trying North Leicester Motorcycles in the UK. He's the largest dealer that I know of and has a lot of parts manufactured if they aren't...
Hi All, I have just joined. Have a Moto-Morini 3 1/2 strada bought in reasonable condition now I am spending some cash to make it look really pretty again. The...
Welcome Bill! Whereabouts are you located? Eric W 500 W Albuquerque, NM ... __________________________________________________ Do You Yahoo!? Tired of spam?...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
