Alright, I need a real Chrysler pro here.. I'll do my very best to describe this problem, since you'd have to drive it to believe it. When driving at any...
The tech doing the alignment should have thoroughly inspected the steering components. But in case he didn't..I would look at the inner tie rods (inside the...
Possibly something wrong inside the rack and pinion unit or with any U-joints in the steering column. Better park it 'til you find the problem or you'll break...
Ugh, the only linkage it has between the steering wheel and the rack is a single u-joint, and it looks fine. I couldn't see it being that.. which brings my to...
The rack mounting points on the crossmember are probably broken out. The sheet metal tends to break at the welds where the nutplates are located. Sometimes a...
Occasionally, when I start my car the alternator/volt gauge will go up and down and consequently the car not to perform correctly. I'll shut the car off and...
I'd guess a ground problem. The 90 Imp was much like a Dynasty, right? Dad had an '89 Dynasty, and that thing had electrical gremlins all over the place... ...
... It sounds like a loose connection somewhere to me. I would start by cleaning and re-torquing all the main electrical connections specifically the battery...
Danial , thanks for the reply. It turns out that I had to replace the Ignition switch to OEM from Napa. Apparently , I got a bad new NAPA switch or Napa switch...
The Imperial and Dynasty are nearly identical overall. The main difference between a 3.3 Dynasty and an Imperial (not all Dynasty's got the 3.3) are: -Imperial...
I should clarify; the Imperial due to the longer wheel base, has longer rear doors. They will interchange with the 90-93 New Yorker 5th Ave, but not the...
It could be bad engine mounts, bad trans mounts, TC shudder, or improper trans fluid to cause a "bump" like you describe. If in park & someone gases the...
What is the procedure in changing my TCM in my 90 Impeerial 3.3L? I don't have the DRB II /scanner to reboot the system? Is it necessary and should I go to the...
My experience is that a dealer won't likely be compatible in terms of scanners that will read computers as old as what we have, however, many good local repair...
Almost forgot, I am remembering that several original problems I had with my transaxle were in fact easily solved by changing speed sensors, if they go bad...
is there any way of recetting the main computer under the driver side dash? The PCM is ok. I heard if i rent and ODBII might do it but nobody is sure. all...
If all you need is to reboot it, just unplug the battery and let it sit for a half an hour. No battery connection will blank out its memory, resetting any...
Double check all the connections. Mine did same after PCM replacement, turned out I didn't have one of the plugs all the way in, even though it sure seemed...
I'm finally tired of the bucking and chugging of my van when idling so I'm getting ready to tear off the top of motor. Several months ago I posted about the...
They go down into the heads. Joel ... From: mopar33lv6@yahoogroups.com [mailto:mopar33lv6@yahoogroups.com] Sent: Wednesday, October 22, 2008 12:32 To:...
Well, got the top off yesterday and found out I'm another victim of the busted rocker arm tower (back bank on the end by cyl 1). The van was a very early '96...
Here's a few pictures of the damage: http://picasaweb.google.com/randy.d.stowell/VanMotor?authkey=fFEyhKtaI6Y# Should have the used head and stuff back by Wed....
I have the early BOSCH ABS unit in my 90 Imperial and apparently it was told to me that I would not have any brake pressure when the system fails. The Bendix...
In a message dated 11/9/2008 7:40:46 P.M. Eastern Standard Time, imp1974@... writes: have the early BOSCH ABS unit in my 90 Imperial and apparently it...
... Hmmm Anthony, this is exactly what I have in my 90 Imperial. I'm trying to remember, my brother owned the car briefly before I did and I remember he did...
Dave, thanks so much. I hope I can get to the bottom of this concern. Do you still own the 90 Imperial with the working Bosch unit? Tell you're brother I'm...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
