The wheel hub seal is blown out on my car. Its completely worn out at the bottom, where the seal meets the half shaft. Anyone know what would cause something...
If the joint is bad enough, yes, it could cause this damage. The joint oscillates, causing the seal to distort. Pull the four bolts from the knuckle, remove...
Hi all, I have a 90 5th Avenue that I somehow switched to the celius(metric) display for the automatic temperature control. How do I switch it back to the...
Hey guys, me again. Does anyone know if the filler tube disconnects from the gas tank? I cant see a way to get the tank out without removing it, but it isn't...
Assuming its a gen 2 or 1 - spray lots of scilicone/WD 40 - around the joint at the tank/pipe. They do come apart - big rubber gasket. easier to put in than...
The tube pulls out (tight fit on the seal), I believe I have a spare tube and seal if you damage yours in the process, but I'll look and see if it still about,...
the filler tube is connected with two clamps,loosen the easyest one to get to and put some pressure on the tube to get it off or twist and pull.that hose is...
... Thanks everyone, for your input. It was alot harder to get the filler tube out than it was to put back in ;) I installed a Bosch fuel pump and new straps,...
... Has anyone else had as much as a hard time as I did reconnecting the electrical connection to the fuel pump? I spent a good 45min trying to figure out how...
I dont recall mine having a boot on it,1999 grand caravan. ... From: fanaticus00 To: mopar33lv6@yahoogroups.com Sent: Monday, March 17, 2008 1:15 PM Subject:...
Hai friends The fuel price is going higher day by day makiing it hectic for all to spend on it . We should take sufficient steps to control the fuel usage...
Greetings all, I'm looking to replace the 6 pistons in my 3.8l V6 (1994 T&C) with flat head pistons. The stock pistons have a recess in the top of the piston...
... recess in ... 2005 ... to ... not ... have ... You should be fine with the newer pistons, but they will rise your compression to a point where you would...
Hello all, I have a question that I hope you don't mine answering if you can. - I was driving this week and on two separate occasion the car would "buck" hard...
I had that problem with my dynasty. I had ended up pulling the tranny oil pan, and replacing the filter, cause it ultimately stopped moving as a result of it....
Rich, thanks for the reply. I have 50,000 miles on the car and I changed the filter and oil at 40,000 miles already. Should I look into changing the tranny or...
Since you already changed the tranny filter and fluid, and it still seems to be doing it, I would say that there is a very strong possibility that it is your...
Rich, I used ATF +4 which is the equivalent to ATF+3 I believe. One question- will I do harm to the tranny if i let it go for a while?- Thanks for your...
The only harm I can see is maybe a spline inside the transfer case being rounded off, but I would imagine that being the worst case scenario. I think the worst...
I'll bet the technician at the transmission shop plugged into the engine diagnostic connector, not the EATX (transmission) connector. Go to AutoZone or...
Gary, thanks so much for answering my message. However, he did use the plug under the steering column. I had disconnected the battery not long ago so he...
Alright, I need a real Chrysler pro here.. I'll do my very best to describe this problem, since you'd have to drive it to believe it. When driving at any...
The tech doing the alignment should have thoroughly inspected the steering components. But in case he didn't..I would look at the inner tie rods (inside the...
Possibly something wrong inside the rack and pinion unit or with any U-joints in the steering column. Better park it 'til you find the problem or you'll break...
Ugh, the only linkage it has between the steering wheel and the rack is a single u-joint, and it looks fine. I couldn't see it being that.. which brings my to...
The rack mounting points on the crossmember are probably broken out. The sheet metal tends to break at the welds where the nutplates are located. Sometimes a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
