Hello all and thank you ahead of time for all your input to this complex question. When my car is hot and I come to a complete stop she has a delay bump shift...
its called a 2-1 downshift clunk, and it happens on a decel because there is no driven torque applied inside the transaxle. the only wy to really get rid of it...
Neal, thanks for the info. I have a 1990 Imperial with 40,000 miles on it. What should I do next? There are no codes showing. I guess I'm on borrowed time wth...
ahh, a 90.... okay, i know for a fact that if this trans has never been apart before, it has the old style low reverse lip seals. whats going on is when is...
Neal, one more question. Is a complete tranny job indicated to repair the low reverse lip seals. And about how much will it cost me and will it last? Thanks...
if you take it somewhere thats reputable, they will build it with all the possible updates, and for just a bench overhaul plan on 1100 at a trans shop, thats...
nope, heres what happens.... you unplug it, or disconnect the battery and the thing may work better until it completely relearns again, your car is too old to...
Would anybody know of where exectly I could locate the coolant temperature sensor on the stat for a 93' 3.3L Dynasty? If it's where I'm thinking, it's almost...
I have a 96 cryslar town & country mini van, 2 years ago it stopped running, it had a bad crank shaft sensor go bad, i had it fixed and it still won't run,i...
Inside the hole it fits in is the torque converter... it has a line cut out in it and as it spins the magnet on the end of the sensor loses contact as this...
Start here: HYPERLINK "http://www.allpar.com/fix/codes.html"http://www.allpar.com/fix/codes.html Your van has OBDII, so you can get a cheap code reader like...
John, you really are to vague in your diagnosis to allow many people to help you. does it have spark, does it have fuelwhat engine, i think only the 3.3 and...
For the past few weeks my wife has had to deal with the rough running of her minivan - 1996 T&C Lxi, 3.8. About a week after the ECU first kicked out a code...
Hey guys, I've never posted here before but its worth a shot. Has anyone done the ball joints on one of these cars themselves? In a Haynes book I have it...
2000 Dodge caravan 3.8 V6 automatic- The engine started making noise in the flywheel area, I pulled the cover off the bell housing and found this piece wadded...
Its the plate that goes between the starter and the bellhousing. It has a distorted O shape, and fills the gap between the starter and the block to keep crud...
The wheel hub seal is blown out on my car. Its completely worn out at the bottom, where the seal meets the half shaft. Anyone know what would cause something...
If the joint is bad enough, yes, it could cause this damage. The joint oscillates, causing the seal to distort. Pull the four bolts from the knuckle, remove...
Hi all, I have a 90 5th Avenue that I somehow switched to the celius(metric) display for the automatic temperature control. How do I switch it back to the...
Hey guys, me again. Does anyone know if the filler tube disconnects from the gas tank? I cant see a way to get the tank out without removing it, but it isn't...
Assuming its a gen 2 or 1 - spray lots of scilicone/WD 40 - around the joint at the tank/pipe. They do come apart - big rubber gasket. easier to put in than...
The tube pulls out (tight fit on the seal), I believe I have a spare tube and seal if you damage yours in the process, but I'll look and see if it still about,...
the filler tube is connected with two clamps,loosen the easyest one to get to and put some pressure on the tube to get it off or twist and pull.that hose is...
... Thanks everyone, for your input. It was alot harder to get the filler tube out than it was to put back in ;) I installed a Bosch fuel pump and new straps,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
