I had a similar problem on my '93 Voyager ... when we started it it sounded like rocks were rolling around under the hood ... I thought the damn engine was...
I'm wondering if anyone here can clue me in where to start to ferret out what is causing my steering wheel to wobble slightly. If I take my hands off the wheel...
hello, i had the same thing in my grand caravan,it was the cv axle going bad. i replaced it and got new ties and an alignment and its straight as a arrow and...
There are a whole bunch of things that can cause what you're describing and they fall into two categories: a) a wheel not running true b) intermittent drag on...
... Check the wear pattern on the tires, look for cupping of the tread or uneven wear to either side, or both. Jack each corner up and spin the wheel as fast...
More than likely, one of your tires is not balanced. This is the cheapest option to try first before anything else. Through this balancing process, the shop...
I'll throw this out to the 3.3 group as well. ... From: Chryslers_MiniVans@yahoogroups.com [mailto:Chryslers_MiniVans@yahoogroups.com] On Behalf Of white93gsr ...
Front wheel bearings From: mopar33lv6@yahoogroups.com [mailto:mopar33lv6@yahoogroups.com] On Behalf Of Randy Stowell Sent: Monday, August 21, 2006 5:22 PM To:...
If you want me to scan the relevant pages from my 1991 FSM, which is probably similar to the 1995 in many respects, send me an email: snewman24@... Steve...
Hmm, wheel bearings - I had one go out on my Town & Country and it was pretty obvious with the noises it was making. I didn't notice any speed related noise...
It took a while but I finally got this concept to reality. Basically I took the imperial front end's folding headlight doors and cut a rectangl-ish shape out...
hey i got a 1992 dodge grand caravan with the 3.3l v6. Does any body know of any companies or shops that make headers for that car? any other performance...
... body ... nope, but soon when i start my own company, i'll be making a line of exhausts, intakes, intake spacers, & quite possibly headers noone makes an...
Tranny ran real good...but I was gutting it to see if any parts or gears could be used in an A413 tranny...I have not found any yet that are compatible, but...
... Seems like you know your stuff on these trannys. I have a 95 A604. What would cause a vibration between 2nd and 3rd? I have what seems to be a lot of play...
1. The way I check the axle shafts on FWD vehicles: A. Jack up the front end, support the weight of the vehicle with jack-stands. The jack-stands must be place...
Question at first I was thinking it was a differential bearing but maybe the it's the outer bearing. The side this is on is the driver's side. I took off the...
The steel bearing support is on the drivers side and the the elongated aluminum bearing support is on the dirvers side. The bearings on the differential should...
Like I said if it was too much work to replace with it in the car I would not do it, I thought maybe if I took the cover off on the driver;s side after pulling...
Ive replaced the bearings in these witout pulling the trans many times. you have to have the right puller the passenger side is the fun one, reason being the...
This is on a 95 Avenger I'm not sure if the trans is on the same side but mine's on the driver's side. I would only attempt to pull that side bearing, cause...
Greetings everyone, If anybody has any calibration suggestions for a 95 3.8L that would be most appreciated. The engine is assembled and ready to be installed....
A couple of months ago I asked a question of why my 93 5th Ave did not coast when going down hill or such. It was suggested that I needed to replace pads,...
I know on my 90 Imperial when I let off the throttle, the lockup torque converter disengages so the car will coast farther. Is it possible your converter is...
I do not know? When I come to the stop sign I have no trouble. The tranny is not locked. On my 85 Chevy the wires are disconnected on the lock up because when...
Trying to replace the rpads on the dynasty. Apparently the style has changed some. The old ones have this metal brace that locks the pas to the caliber. The...
Hi all, I am looking at the possibility of swapping a set of leather seats from a 93 5th Avenue with power to 90 5th Avenue that has only a power driver seat. ...
Is there any difference between the 3.3 and the 3.8 intake plenums for the mid 90s versions? I've got a 3.8 Grand Voyager, I'm looking to port the manifold,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
