I ABOUT TO STEP UP TO A 2 1/2 PIPES, IN THE PAST ON A DAYTONA I REAMED TO CAT OUT. WHERE I LIVE THERE IS NO SNIFFER TEST. MY QUESTION IS WHAT EFFECTS WOULD THE...
What year? Pre-OBI2, there is no affect...I run my 1991 AWD Caravan without a cat. Post-OBD2, you may get a code for it, but you can ignore it if there if no...
Of course, with a highflow cat you shouldnt get any measuriable power loss or restriction from the cat unless its clogged up- thus its better just to throw one...
Hello! I'm a new member with two Gen 2 vans, a 92 and 93. The 93 has a blown trans. Anyone out there really an expert on these trannies? It's my understanding...
To bad you didn't post this last week. I have a factory (third party) rebuilt on my floor supposedly with all the mods and updates, never been in a vehicle. I...
okay, im a trans guy. the bolt pattern for the 3.3l 3.8l has never changed after 96 they used a new style top mount on the back of the trans that went over the...
I don't think the bolt pattern has changed, but electronic differences prevent interchanges except within a few year ranges. 93-95 is listed as a direct...
... Upgrades? The factory changed stuff as the A604's design progressed. Just about every year the A604 changed starting in '89... the differences were mostly...
I forgot to ask.... How do you know your tranny is shot? Have you run a CVI test? I know that a A604 can be made to look like its shot if there's something...
You got it almost exactly backwards...technically ALL A604s use two speed sensors (input/output), but pre-94 the speedo/odo were controlled through an...
There are more serious changes besides the speed sensors. Even an early 96 tranny won't interchange with a later 96 tranny because of the differences in the...
i live in an area that has nnow sniffer test. If i ream my cat out what affect wll this have on my computer? i;ve done it before, i am moving to a 2 1/2 in...
If your 3.3 is a preOBID2, the comp wont notice it. But I have to say as a side note- that your state may not snuff test now, but it very well may in the...
thanks for stating that mark the only thing worse than no info is the wrong info. like i said before, ill build you a correct 604 for 700 plus shipping,...
the mileage/trip/directional module just suddenly fried,a little smoke and the tell tale smell of electronics melting(a capacitor and diode)inside the corner...
I would think the only thing that would do this is a short in the wiring at the unit. See if the wires are bare anywhere and touching a metal surface. Tom...
It's an OBD2 and I'm sure you would end up with the check engine light on if you hollowed out the cat. You can get 2.5" hi flow cats for < $200 and have it...
I would go to the dealer and grab the FSM pages on the EVIC. Go in with a multimeter and make sure all the pins are still what they should be (aka ground still...
Adding crap to the dynasty ... ok few questions, first i am wondering wre do i connect the tach sensing wire on a 1991 dodge dynasty le with the 3.3l v6 with...
My tach is wired in using the CRANK sensor as the tach's input. I have heard, but have not tried using one of the timing signals (there are 3) on the coil pack...
The tach signal is almost always pin 43 of the engine computer. Mark 1992 New Yorker Salon 53K and a moonroof 1999 Chrysler Town & Country LXi 1990 Chrysler...
Yesterday after lunch I started the Imperial. The climate control went on as usual and as the system was moving "doors" to put cold air through the dash vents...
If you are lucky, maybe you only lost vacuum to the system. Look under the hood for a small vacuum line running into the firewall. If it's damaged or became...
You should hope it only the vac line. I just took the entire box out of a 92 Dynasty that I am parting out. Now I have to put it into my 92 Imperial. I have...
--Boy... Things are really "busy" around the master cylinder/booster in this '90 Imperial! There is a really small line that goes through the firewall(about...