I am looking for a 3.0, 5 speed manual transmission,front wheel drive auto, possible a 93. i need the complete car for a transplant into a small motor home....
Hi, I don't want to do it but I am having trouble finding a job and have some bills due and so I am forced to sell my baby. I am just waiting for my tax refund...
any one ever try to fix the rocker shaft tower that breaks off at the head and makes this awful ticking noise that gets louder as the rpm's go up....i think i...
how do i know what my throttle body size is on my 1991 3.3 caravan c/v? and can i get a 3.8 engines throttle body to gain any H.P.? or a bigger one at that? ...
yes,allpar is where i saw the fix for it. if you did not use the helicoil...did you just thread it same size as the stud from top was and use a longer bolt? ...
well that didnt answer all the questions i had. but thanks for the info so far....now for the rest of the questions... can i put a bigger throttle body and...
If you can get it to fit, and the cabling for the throttle/cruise is in alignment, and the TPS is sending the correct signal, then technically yes you can get...
You'll need to ream out the threads in the upper (broken off) section, and drill/ tap the remaining hole in the lower portion a bit deeper. Be very careful not...
You'll need to ream out the threads in the upper (broken off) section, and drill/ tap the remaining hole in the lower portion a bit deeper. Be very careful not...
hello all, i was told theres a way to run ur vehicle off of prpane and that it gets better mileage than gasoline...is any of this true? and can you use propane...
i have a 91 dynasty with a 3.3 liter v6, and its fuel rail is leaking at the crossover pipe connections, it leaks a lot and i need to know, if this was ever...
... need ... to ... The same thing happened on my 92 Chrysler Imperial with the 3.8 V6. I ended up finding a used one from a guy in California (I'm in ...
Hi Someone just posted a message regarding the fuel rails in the 3.3V6 cars. I have got the exact same problems......again....for the 4th time in 3 1990 New...
I'm making plans to attend the Mopars in the Park show on June 4 and 5, 2005. This is a huge Mopar show that runs both Saturday and Sunday. If anyone on the...
I have a '94 Chrysler Town and Country with a 3.8L engine and A604 Tranny. Lately, I have been replacing the driver side CV axle every 2- 3 months. The inner...
Too much angle (caused by the two suggestions so far -- essentially improper alignment/movement) will definately cause this problem. However, my question is...
To answer your questions. I have replaced the entire left front CV axle with a complete axle assembly. As you point out they are so cheap that it is the...
Hi, I don't want to do it but I have some bills due and so I am forced to sell my 1990 New Yorker 5th Avenue. The details: The car is a white New Yorker 5th...
a few years back i went though 9 drive shafts before i found out it was a broken trans mount. i would check that out because that would deffently eat drive...
I have the 3.3 in a 99 Grand Voyager. I love the versatility of the beast but the 'cool' factor is sadly lacking. Last month I ran over a cement block in the...
gowritch <gowritch@...> wrote: I have the 3.3 in a 99 Grand Voyager. I love the versatility of the beast but the 'cool' factor is sadly lacking. Last...
I'm currently working on heavily modifying my 91 Caravan AWD (3.3l). My exhaust setup exists of essentially no cat, stock muffler (in the dumbest place ...
I have noticed that some boards, like the intrepid board has toyed with the idea of throwing the 3.8 crank & rods in a 3.3 to get a 3.5. Has anyone here tried...
I could see where this might make sense in an LH car where there is no 3.8 option since it mounts differently. However, in any other car, I'd just go ahead...
OR simply bore the 3.3 out to 3.8 specs - A forum of engine rebuilders I was reading had suggested that rebuilders should use 3.3 blocks bored to 3.8 standard...
I replaced the timing chain on my Caravan at 107k and did not know about the need for a spacer when I reinstalled the original cam position sensor. The engine...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
