Is the walbro still for sale? _____ From: mk2@yahoogroups.com [mailto:mk2@yahoogroups.com] On Behalf Of Shiva Goel Sent: Thursday, August 24, 2006 10:09 AM To:...
I'm still wanting a roof for my '85 and got to thinking about the Maxima and Accord back then. They both came with a glass roof. Did any of the Supra's have...
I vague recall that someone fitted a glass roof from a Honda Prelude which had the same dimensions, but don't recall what year except that it was a late 80s I...
I vaguely remember a LONG time ago that TomD posted something about the Cressida glass (I think???) roof working on our vehicles...I always wanted to check it...
OK, has anyone besides myself and Mike Lewitz experienced the Addco sway bars rubbing the crank pulley under a hard braking instance?! Kinda sounds like a...
are your motor and trans mounts solid? if they are, i don't know if it's how straight your car is or a problem with addco. in any case, while you figure that...
Dave, you can try to add some shims (wide washers will work) under the motor mounts to you can use solid steel motor mounts, those won't deflect at all under...
Armin, You get deflection with solid motor mounts? The ones I make and that HPF sells don't deflect. I don't make them for the 1J but how did you make them? ...
Your transmission mount may be broken. Mine was, I didn't even notice it until I unbolted the crossmember from the car and half the mount was on the tranny...
Discussion about Toyota Supra MKII ('82-'86)I've had 6 MKIIs with addcos, and never had any rubbing issues. I also have very upgraded brakes on my 7M-GTE...
This is probably what I'll be doing. Seems like it's the easiest and quickest way to remedy the problem. Thanks guys! Dave 92T & 84 P-type Mesa, AZ ...
Hi Everybody,I'm selling my 82 Spearco Supra,it's all ready to go,california smog is good until october.You can find pictures of it on craigslist.com for the...
All If any of you have had this kind of problem, I'd like to know how you overcame it. Seems like every year I have to replace a fan clutch due to the one...
Verdun, As long as you have a factory unit you can go down to Toyota and by the gel that goes inside the clutch. Take it apart, clean it out install the new...
I finally got around to checking amperage usage in key locations with my trusty amp probe. Mind you, it's a 7MGTE w/80 alternator. Measured at the alternator...
Ok I'll try that Jake <notusable@...> wrote: Verdun, As long as you have a factory unit you can go down to Toyota and by the gel that goes inside the...
So Jim, are you saying that there was heavy resistance on the factory wiring, or that current is not going through the fuse box anymore? Don't understand the...
The bigger wire was taking the load off the engine fuse box. 20amps going through the big new wire, remaining amps going through the factory wiring. _____ ...
Verdun, That was given up in the early 70's. If you're going down the highway you don't need the fan. So the clutch will disconnect it. If you have it ...
i just picked up an 85 mkII and am trying to get the lil old 5m going again till i get the 7mgt swap done. it's acting very weird, and when i got it the...
Eric, Sounds like you are on the right track. The 5M is a distributor motor so no TPS. Other than the items you described I always start off looking at the...
yeah i am going to check the base timing out and see where that is because they changed the belt not too long ago and it may have been done wrong. and the tps...
yeah, found that the crank pulley bolt was loose and i guess never torqued the last time someone changed the belt. now i have to strip it all down and redo...
Techna-Fit stainless steel braided brake line Group Buy, ENDING SEPTEMBER 30, 2006. Being organized through CelicaSupra.com They can order any brake line kit...
Dave, Is there some way to buy in on the group buy without being a member of cs.com? Jake _____ From: mk2@yahoogroups.com [mailto:mk2@yahoogroups.com] On...