Has anybody had the problem, or knows of a solution to the front brakes locking up when trying to stop. I know that there is no weight on the front wheels to...
Kennedy Engineering used to make adaptors for Mazda to VW transaxel as well as clutch kits. A Mazda is a great conversion but the radiator is the issue. ... ...
If you have a VW pan its very difficult and expensive. You are limited to a very few engines and a conversion is going to be very expensive. I would sell the...
Hello - I recently purchased a 1952 -TD replica that was being relocated to NY from Arkansas. The transport was a 3 car rack. In the 1st slot a hurst was...
HELLO AGAIN - I WROTE A 2ND NOTE SINCE I WASNT SURE MY 1ST NOTE WAS SENT TO YOU .THANKS I RECEIVED A COPY of my 1st note. IM 65 YRS. OLD AND DISABLED FROM...
Sounds like they're getting too much pressure or there's grease on them. Are they disc or drum? If disc, do you have a proportioning valve in the system? If...
Kenneth; I think you will find the rubber hoses to be the problem. What happens is the hose deterioates from the inside and turns into a one- way valve. When...
Not sure if you have run into this yet, www.b-rodorcustom.com web site or found by typing B Rod or custom as well. This company has put together a beautiful...
Thanks for the input about B Rod. I think I have just found my all time dream car. It is hard to imagine improving on the TOMCAT. All the best lines of the...
Thanks for the input about B Rod. I think I have just found my all time dream car. It is hard to imagine improving on the TOMCAT. All the best lines of the...
Hi, I recently saw some conversation about a company that does some custom (more hot rod) work to our MGTD kit cars. I must of deleted this session of emails....
I recently aquired a Fiberfab/Pinto 2.3L powered MG-TD Kit that is semi- finished. I have the vast majority of the original parts kit. Unfortunately I haven't...
Tom I was getting ready to do that, I was replacing a 009 distributor. However I found that I would have to replace the fuel pump because of the size of the...
I have the same car. I'll pull as many measurements as I can tonight. It appears to be pretty simple to make from tubing or conduit. I do CAD work all the...
Tom Installed Pertronix on a 009 about 8 years ago. Installation was simple and have not had any problems. Also recall it required coil to be changed. Ran...
I think MG Magic has them. They are closed until March. Phone 954-680-2010. I am almost finished with my Pinto MG. It takes time! I would like to see...
Here is a drawing that I made after measuring my bows this morning. Hope it helps. If you already have a top, but no bows, you may want to 'fit' the bows to...
I also have a Pinto MGTD that I am putting together. Does anyone know what the correct measurement is from the windshield to the to the back shoulder of the...
I'll measure in the morning. I lowered my seats by 2 1/2" and have the back of the seat slam up against the raised area for the back (seat). It is very...
I have a Chevette based MGTD. I also lowered the seat by about 2 1/2 inches and I raised the back so I could move it back. The car is much more comfortable to...
Ed Summers
edsummers@...
Feb 23, 2008 1:48 pm
3743
Bob, I measured at the center of the car, from the base of the windshield just behind the rear view mirror to the inside edge of the back shoulder of the body...
Thanks, I would be happy to, with the moderators permission. James Clifford James <cgj7333@...> wrote: Very Nice! I hope you add this drawing to the club...
Hi all, Here is a list of the British Car Events happening in Southern California. All of these events are FREE and all are welcome. Southern California -...
... Hi Tom. Pertronix makes several different types of electronic ignitions. There is one, the Ignitor, that replaces the points and condensor in a 009...
THANKS James. I didn't expect such a quick response and it is appreciated. I have a problem though, I can't open the attachment. It says the file is not...
Thank you Bob. If I can't form them myself, I'll give them a try. ... 680-2010. I am almost finished with my Pinto MG. It takes time! I would like to see...
