If you are going to the Junkyard to get an EDIS4 here is what you will need. I was just there and got 2 EDIS4 modules, crank pulley w/36 tooth wheel,...
Now that I have my toothed wheel I am going to attach it to my crank pulley. Does the missing tooth need to be set at a particular position relative to the...
Somewhere on the net about 6 months ago i saw a web site in the US selling uprated EDIS coil packs for the Ford CVH or Zetec. Now i want one i can't find the...
Hi Jim Try these http://www.spiderautomotive.com/coilmsdfored.html http://re-racing.com/Merchant2/merchant.mv?Screen=PROD&Store_Code=RE&Product_Code=ACI-140018...
... crank pulley. Does the missing tooth need to be set at a particular position relative to the engine timing? I just need to know if the missing tooth...
Those are made by accel (140018), the red ones are from MSD (8241). Take your pick. To help, here's the specs I've found somewhere: FORD SUPER EDIS COIL PACK...
Thanks for all the info, the yellow one was the one i was thinking of, now all i've got to do is go through them and find one who will ship to the UK. Jim ... ...
Hey Jim, I was thinking about this earlier. The cheapest one that I saw was on the doug herbert site. This is were it get's complicated, so bear with me. There...
Place piston no.1 on 90 deg btdc. Attach wheel with sensor in line with the missing tooth, any where you like. SFC ... From: Paul Dykstra To:...
S.F.Cillari
sf-cillari@...
Nov 2, 2003 9:26 am
922
In short, the position of the wheel relative to the engine isn't directly important. At TDC, the missing tooth should be the correct number of degrees past the...
CROSS-POST I've just sent the follows to Megaspark - please followup in that group. ... While trying to develop megasquirtnedis Dave Haynes and I have ...
I guess i'm a little responsible for the 22.5 deg delay. I used the megaedis code from Tom to run my exp. vw motor. First I had some jitter when reving above...
S.F.Cillari
sf-cillari@...
Nov 2, 2003 4:12 pm
925
Yeppers, 19mm it is, RH thread. Be sure to have some way to lock the crankshaft from turning when you remove that bolt, and have some bigger screwdrivers to...
Hi all, I'm building a kit car with a VX 2 L 8 Valve engine in fitted with twin 45 webers. I've been gathering info on the MJLJ, and was about to build one...
... See the MegasquirtnSpark Files section for the correct input signal circuits. You need a vacuum hose connected to the best vacuum source you have. As you...
The web site http://www.dainst.com/info/edis/edis.html lists the 1990 Escort EDIS4 module parts number as F1CZ-12K072-A I have 2 EDIS4 modules one is part...
I went out for a ride and while driving back into the garage, the engine began running very poorly, sputtering and poping. I noticed that the trigger event LED...
You can take a length of rope and poke it down a spark plug hole leaving a bit hanging out. The rope will stop the piston and the crank. Once you get the nut...
I found one car with cap screws and accidentally broke the sensor all the others I found were torx. Rodney Sparks <rodney@...> wrote:Also, FYI, some of...
I was concerned about preventing the crank from rotating before I went to the JY but I found several cars with the head removed and the pistons frozen in...
Where on the escort/orion is the module located. Someone said near the right headlight??? I couldn't find one on the escorts i searched... ... all the others I...
I found them located on the right fender behind the headlight if you are looking at the front of the car. It is smaller than I expected it to be and mounted...
Do they look anything like any of these: http://www.krogslund.dk/catalog/images/1965006.GIF http://www.krogslund.dk/catalog/images/1965009.GIF Just wondering...
Nope. Here it is: http://www.rsparks.com/megasquirt/edis1.jpg http://www.rsparks.com/megasquirt/edis2.jpg If you're standing in front of the car, look to your...
Hi All, Just a comment on this; depending on the motor, it might be worthit to determine which stroke you are on; if is not the compression stroke there could...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
