Now there is hope for inductive pickups and MSS! I did the first attempt to start with MSS v2.986 and a time based low speed timing, and it started at once!...
Hi Rick! To run distributorless system you need some kind of multitooth setup to know what coil/plug to fire. Normally the distributor does this plug selection...
I was wondering if it's possible to use only one edis-4 module to drive two coils for a 4cyl twin spark engine, or do I have to use also two modules? The...
Awesome, great work Magnus. I am patiently waiting for the software upgrade to finish my conversion to MSS on the nissan 280zx turbo. Bryan ... low speed ... ...
... low speed ... engine (10 ... some other ... Wonderful news! MSnS with the base 3.0 code AND inductive pickup compatability..I love it. Excellent work...
I'm playing with the MegaSquirtnedis code, and am having compile difficulties. I've gone back to the original unmodified code, and compile attempts produce...
Hi Jesse,I've been chating about this and this is one way that has been proven as it is 90% OEM parts and tried and tested etc.Anyway this is what I wrote....
Arrrgggg stupid browser buggered up my diagram but I notice when I am writing this reply it now looks correct so perhaps if you reply or pretend to you can see...
... timer ... Strange... can you compile other things ok? I can't see what is wrong with that code - that is unmodified from megasquirtnspark. James...
James, Yes, I've compiled a variety of other code versions without problems. Are you using CASM as well? I'll try the original MSnS code, and see if that runs...
Thanks for the information. I did some research about the memcals the other day and found some information. It appears that there are MANY different versions...
Hi All, I'm new to this group so please forgive me if this question has been said before, I've had a look in the archives and it appears not. I've just been...
Hi all My name is Gustaf, and I am very delighted to see a simple solution for running programmable ignition within the MS. I will run MS&S on two engines (if...
Hi, ... Check the meaning and _direction_ of PIP and SAW carefully http://www.squirrelpf.com/msavr/index.php?page=EDISIgnitionModule IAC signal is output from...
Hi, ... With the hammer approach ? Does it help if we have a hardware (not interrupt) counter in the uC, which we can check periodically (say every 1 ms)? At...
Hi Marcell, That was a typo, sorry. Obviously so though because the PIP signal is required to drive MS, my MS would hardly be running if it were taking the SAW...
Dave Have you tried it on the stim? You should be able to see the FIdle LED flickering, if you don't have a 'scope to check it on. My EDIS and MS have yet to...
... on ... How many cylinders on the engine? Four pot is known to work but there appears to be a bug with 6 pot which I have yet to investigate. If you are...
am I using the correct output? I'm using the fast idle channel output on my MS. Should I be using one of the LED outputs instead? I don't have a stim...
Hi James, All I've got is a 1k resistor wired over the diode D9. the other resistor you mention in your instructions is on the input side and that's all...
Hi All Here is a picture of an EDIS8 module up close with the R values marked. If any of you can't sleep at night you could draw up the schematic. Does anyone...
I've got one of those Velleman things (won't risk my HP or Tek scopes in the garage!), but it isn't to hand 'cos my garage is 30miles from my front door :-( ...
JM> Ah! I think you have found a bug in my code. I only tested with it JM> set to 180degrees. This means that it will only work on a 4pot until JM> I fix it -...
I'm VERY curious and interested in this software update, but have a question to ask.... What speed is the code running at? The 'standard' B&G code is running...
OK, I'm dumb. The rpm issues I mentioned were due to me having the MS configured for 4cyl, but 120deg sense for the spark section. D'oh! RPM indication is...
... The same. It is about 1us - it has the same resolution as MSS. The injector code generates an interrupt every 0.1ms and decides whether to open or close...
Busy evening :-) Now changed the SAW formula SAW=1390-(SA*8) to be 1454-(SA*6), and have a good pulse width. Maximum error equivalent to -3 degrees at 55 ...
... The PIP signal is generaated by the EDIS box and should go to the modified tach input, the modified MS generates the SAW (Spark Angle Word) pulse out via...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
