guys ,can the sensor on EFI car throttle body be use instead of the on board sensor in MS. the wire type available on most cars. can the the out put of these...
what you are refering to is a MAF sensor and measures air velocity rather than MAP that measures pressure, there is a way to use it but not the way you think,...
There are MAP sensors on some throttle bodies. Can't remember what make and model (throttle body for PFI, not TBI) IIRC, Toyota did that on Z series Corolla...
Clare Snyder
clarence@...
Dec 2, 2007 4:23 am
3890
that is true, but the type of sensor which was asked about - the type with a wire - is an air flow sensor. ... From: Clare Snyder To:...
Email Matt at DIYautotune.com. He can tell you. ... From: poodina1 <poodina1@...> To: megasquirtnspark@yahoogroups.com Sent: Saturday, December 1, 2007...
Thanks guys, have got the info I wanted. Was trying use the senor of Suzuki to calculate and did not know if it would work, and yes it's MAF senor. thanks a...
The engine is a 2.2l 16v turbo out of an Spirit R/T. Stock it uses a crank trigger at the flywheel. The flywheel is notched .... looks to be oddball spacing. I...
... Isn't that on the MS website? http://www.megamanual.com/v22manual/mtabcon.htm ...look about halfway down the page. Both are there, and the 2.2 board is in...
only circuit diagram is present there noitnPCB layout.... the pdfs are also the same as the once on the site... there is no PCB layout ,designing one from...
I'm MSNS&Eing an '81 Kawasaki 1100, using a v2.2 board. I'm putting together the board for the Vr signal conversion/second pressure sensor for real-time baro...
What are the jmp [JS0-JS11] on the Microcotroller pins in the Version 3 pdf. They do not seem to connect to anything? what are they used for ? are they use at...
hi, this is from a post a couple of months ago... It's all shifted over to: http://www.msefi.com/ http://www.msextra.com/ The email groups can be found there. ...
the project: 1981 Kawasaki KZ1100 6-1 wheel, Ford DuraSpark VR sensor MS1, v2.2 board, MSNS wasted spark I built this board originally just as an MS1 and used...
if you're willing to wait a week or so, you could order two of the optional high current coil drivers (VB921) and just trigger the coils directly with the MS....
Consider using your stock coils and the MSnSE code without an external ignitor. My experience: I tried to use a Neon coil-pack with a Toyota dual-channel...
After having all sorts of problems with my wideband controller I've decided to use it only for tuning, then return to the stock NB sensor for daily driving. ...
Can Megasquirt fire a set of Denso pencil style coils on plug off a Suzuki 650-1100cc bike to fit a 6 cyle aircooled auto engine? I have the plug coils,...
Absolutely. These are inductive ignition coils. You do need some ignition power modules between the coils and the megasquirt, VB921, some sort of IGBT or an...
Balbur, thanks for the input. I will pursue the COP idea further. Would it be OK to run waste spark on an engine maxing at 5,000 rpm? I presume coil...
This isn't exactly the same setup as you're contemplating, but I've run Denso COP's (from a Toyota Supra, which were not equipped with ignitors) on a Lexus V8...
HI, It also depends on the type of coils you have.The Denso bike coils I tried were from a CDI system. although the coils worked the spark was not really good...
Gerben, could you advise on what VW models these coils are found. (Thanks HTH for the MJLJ link). Erik ... tried were from a CDI system. although the coils...
Hi I have a Seat Ibiza Gti 96 is has the same engine that the golf gti 96. It has no ignition module, what I supose to do? there are some circuits on the net...
