hi all, i am just at the 'considering' (ie reading, thinking, fantasizing) stage of the game, but have an issue about the EDIS 36-1 crank wheel. of all...
Hi My name is Daniel I live in Brazil and have the preparation workshop look this www.fueltech.com.br www.proautomotorsports.com.br i like megasquirt thanks ...
the size of the wheel and speed have effect on the voltage produced by the VR sensor of the EDIS; it is more likely that you would run into problems with the...
hi i am running ms1 v3 board with vb921 ignition driver i get spark and it was running badly i had and then it just stopped one day i still have spark but no...
Another question i need 2 set up the antilag with the ms1 v3 board so how do i get it 2 retard the ignition 40degrees and still inject fuel when it is turned...
I assume you've picked up the anti lag code I wrote last year. You have to use the version of megatune supplied with it and enable the anti lag in the anti lag...
thanks rick for the comment. short answer to your question is: no, i havent really considered other options, and i think i might just sit back for a bit and...
I've been wondering the same- I notice the actual metal "tip" of the VR sensor on the EDIS is much smaller than the wheel is thick- about 1/8" for the sensor...
hi will, that is exactly what i was thinking. i will just have to do the test and report back.... could be a while however (!).. i am just trying to get this...
I am converting a Lotus for megasquirt and spark - extra, I have considered using EDIS but then I realized that it would use the same amount of outputs as a...
you don't have to use EDIS4, the EDIS8 will work just as well if you use half of it. figuring out which outputs to use would be the trick ... All-new Yahoo!...
hi rick, what model lotus are you converting? can i trouble you to elaborate on your comment a little, as i dont quite understand your point. particularly i am...
I would like to know, will this system work with the stock wiring of a 1988 2.3L turbo coupe as far as the EDIS replacing the distribitor. I need this info....
Have a look at these sensors: http://www.cherrycorp.com/english/sensors/gs1012.htm They're supposed to be much more sensitive than a VR, and output a very ...
I'm converting a 1974 Elite, my plan is to have ITB's and wasted spark ignition using trigger wheel mounted to the back of the crank pulley. The EDIS setup...
Anthony, I have a 1988 Merkur XR4Ti with a 2.3L turbo so I am very interested in whatever answers you get to this. Good luck James...
James Wieler
jameswieler@...
Oct 7, 2006 3:56 am
3844
Rick, When looking at running ignition directly from MS as I will be doing on my cobra replica. The websites do advise fitting another plug for the ignition a...
The problem was never the number of available pins on the box connector. I'm actually running a modified MiniMS board with MIL-spec connectors. The problem was...
Ah! Got you now. ... connector. I'm actually running a modified MiniMS board with MIL- spec connectors. The problem was the total number of outputs available...
Got the cobra started last night. Yippee!!! Running MS1v3 and driving coils directly using 36-1 toothed wheel. Getting there slowly but surely. Manifolds on...
None of the TurboCoupes were EDIS. Hence, the stock wiring is not plug and play compatible. If you don't need wasted spark, I personally would just use the TFI...
Hi have a ms1 v3 board running a single coil vb921 ignition driver on a cosworth turbo and had it running for a while then it started cutting out and reseting...
I have a MT file setup for my car i want someone to take a look at to see if im in the right direction before i start it and start to tune. I cant attach it...
If all the information you entered in the "generate table" function is relatively accurate, then the basemap should at least start the engine. From there you...
I'm gearing up to squirt my Volvo, it's a 1984 242 Turbo currently running the stock K-Jettronic mechanical injection which has caused me much hassle over the...
