im going to run methanol on an fj1100 yamaha dragbike im going with the recommended sensor for intake temp(gm item)what do i do for the engine temp sensor...
AFAIK E100 (100 percent Ethanol) requires a catalytic ignition, doesn't it? E85 I think will run with normal spark plugs, and might be a better choice...
thanks but im staying with methanol-rc engineering told me that it would be no problem as long as i flushed the system with gas at the end of the race day___my...
Personally (and depending on the head and the thermistor- I assume you are using a GM type NTC type) I think I'd drill and tap a pocket into the head that held...
found a company called omega that has bolt on thermocouples-look like a wire with a bolt hole on end that i can just bolt to the engine fins-they are rated to...
since i have an air cooled engine thinking of a thermocouple instead of a thermistor-my son says it wont work because on is a voltage thing and the other is a...
No, your Son is right- a thermocouple CREATES voltage from heat (like a battery), a thermistor changes it's resistance so that when a fixed voltage is applied,...
... From: "sherwood shute" <nealmeal2000@...> To: <megasquirtnspark@yahoogroups.com> Sent: Tuesday, July 04, 2006 3:58 PM Subject: Re: [megasquirtnspark]...
Clare Snyder
clarence@...
Jul 4, 2006 9:46 pm
3820
ok i now realize that the engine temp sensor for a watercooled engine is called a themistor and it should work fine in my air cooled engine if i drill and tap...
There are number of air-cooled engine thermistors that you could use. Porsche 914 used a simple thermistor that was mounted in the cylinder head, if you cannot...
hi all, i am just at the 'considering' (ie reading, thinking, fantasizing) stage of the game, but have an issue about the EDIS 36-1 crank wheel. of all...
Hi My name is Daniel I live in Brazil and have the preparation workshop look this www.fueltech.com.br www.proautomotorsports.com.br i like megasquirt thanks ...
the size of the wheel and speed have effect on the voltage produced by the VR sensor of the EDIS; it is more likely that you would run into problems with the...
hi i am running ms1 v3 board with vb921 ignition driver i get spark and it was running badly i had and then it just stopped one day i still have spark but no...
Another question i need 2 set up the antilag with the ms1 v3 board so how do i get it 2 retard the ignition 40degrees and still inject fuel when it is turned...
I assume you've picked up the anti lag code I wrote last year. You have to use the version of megatune supplied with it and enable the anti lag in the anti lag...
thanks rick for the comment. short answer to your question is: no, i havent really considered other options, and i think i might just sit back for a bit and...
I've been wondering the same- I notice the actual metal "tip" of the VR sensor on the EDIS is much smaller than the wheel is thick- about 1/8" for the sensor...
hi will, that is exactly what i was thinking. i will just have to do the test and report back.... could be a while however (!).. i am just trying to get this...
I am converting a Lotus for megasquirt and spark - extra, I have considered using EDIS but then I realized that it would use the same amount of outputs as a...
you don't have to use EDIS4, the EDIS8 will work just as well if you use half of it. figuring out which outputs to use would be the trick ... All-new Yahoo!...
hi rick, what model lotus are you converting? can i trouble you to elaborate on your comment a little, as i dont quite understand your point. particularly i am...
I would like to know, will this system work with the stock wiring of a 1988 2.3L turbo coupe as far as the EDIS replacing the distribitor. I need this info....
Have a look at these sensors: http://www.cherrycorp.com/english/sensors/gs1012.htm They're supposed to be much more sensitive than a VR, and output a very ...
I'm converting a 1974 Elite, my plan is to have ITB's and wasted spark ignition using trigger wheel mounted to the back of the crank pulley. The EDIS setup...
