I think you'll find most folks use the VR trigger from a ford Edis System. not magnets. 36-1 tooth steel trigger wheel and the sensor is all ya need. ... From:...
I am helping a group install MSnS on an '84 BMW 325e. We believe that everything is wired up properly, but are having trouble getting any spark. We are using 2...
Hi Philip, I have not played with the HEI yet so I can not give you any real troubleshooting input. But the look up power is to allow a full sweep of the ...
OK, awesome. This reinforces my understanding that I have developed since I sent that message. I think I have discovered the problem that I was having,...
I would recommend bypassing the relay board completely, I have found that it is a noise amplifier for crank signals. Thank you, Mike Lough LoCustom.com ... ...
Hi, I have a Rover 3500 V8 engine with a worn Lucas 35D8 distributor. I'm considering installing a Pertronix Ignitor (LU-181) or Ignitor II (9LU-181) unit to...
i'm running a petronix ignitor, but using it as a trigger for a Crane HI-6S with PS60 coil with NGK iridium plugs on my volvo, only i found wrong with the...
I would use the Ignitor I. I'm using one in my volvo as a trigger for MSnS. Wiring diagram here: http://1800philes.com/images/rebuild/pert.jpg steve...
Hello, Firstly, my apollogies if these questions have been asked before but this whole subject area is so complicated it's difficult to dredge through all the...
Hopefully you will get some good news from the list members that are in the know. I've been wanting the same thing for my motorcycle application for almost a...
I have a similar engine configuration with 4 independent runners with (origionally) a pair of NDIX 36 2bbl carbs converted to 4 separate throttle bodies. I...
Because Megaspark is for a distributor system. I want one that can control a dual coil waste-spark system. It seems like this would be easier than a...
... The distrubutor for a dual coil wasted spark system is actually any kind of conductor...;-) Seriously, I'm starting to use MSnS on my Norton twin by...
The 1k resistor is there to limit current. It goes on the base of the transistor which goes to x2. Emitter goes to ground and collector to your relay. ... ...
i agree, its so easy to find on ebay so if youre looking for a ms search for
it! or look at the sales forum on msefi. dont pollute the yahoo list with...
I am currently building a megasquirt and require some help. I would like to use a Pulse output for fast idle as well as having an ignition output for the coil....
I can find the kits but I am not sure what is really needed. I am installing a SRT4 motor in an Omni. I need full engine controller so I guess I would be...
I went to the MegaSquirt webpage, and found MegaSpark. I followed many links, but couldn't find a link with kit info. Help !? ... From: Kevin Franzen Date:...
go to msefi.com and look at megasquirt and spark extra __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the...
Upgrading to Spark requires no additional hardware from boggsflex, just the coil packs or HEI or EDIS whatever you decied to run it with _____ From:...
The MSII chips are out 'till later this summer. I bought mine from DIYautotune. Ordered on Sat arrived Tuesday. Assembled on Wednesday. Everything labeled and...
I will be out of the office starting 04/25/2005 and will not return until 05/06/2005. I will contact you when I get back. Please call Bhags Nana in case of ...
Hi im curently setting up an 5cyl engine with msns however i want to make sure which setting i must use to install the hall effect. At tdc it is low 0 volt,but...
