Have you checked VWVortex.com forum's yet. I did a search for "megasquirt" and a couple of threads showed up with people either sharing base maps or willing to...
I have a Scirocco 8V 2.0 swap that I'm being asked to help with, apparently the spark and fuel is all ruined, and it won't pass emissions. The only issue I...
Peter, I would suggest checking VWVortex.com and their regional forums. You can IM or e-mail Polizei_99, he's on that website and he is in Vegas. I think he...
im going to be using my FIDLE output, so i understand i need to change the d9 diode to a 1k resistor, but how many watts? what about the %? All is says is 1k!...
ive been running MS in my car for about 8 months now, i decided to upgrade to spark control so i did the suggested hardware and wiring changes to the board,...
... Update: the Bosch motronic coil with integrated "power stage" is not smart-dwell according to the folks at msefi.com. so it's not for MSnS, unless perhaps...
Hello everyone. I have Pontiac Sunfire that uses dual coil packs for a dis waste spark ignition system. That is 2 coil packs for 4 cylinders. Spark trigger...
Just letting others know that if you order MS from Glen's Garage you might have to wait over 3 months (!) like I am. I'm still waiting. There is a thread at MS...
Glen is a great guy - his kits are put together meticulously. However, I see a LOT of "builders" selling MS units that are Glens Garage kits and I think Glen...
Oh yes Scott, that's totally my opinion also. Glen is a good guy. I've alsways said so and I'm sure I said that a few times in my original post. And, I too...
Hello, Apologies if this has been answered hundreds of times in the past. I'm planning to upgrade a n/a, carburetted, Fiat t/c engine to fuel injected,...
... Excuse my ignorance but why is wasted spark a bad idea on forced induction? I've been running wasted spark on my cosworth engine, as do many others and ...
Darren; First off, wasted spark is OK- but a number of the FIAT guys that are running turbos have gone over to COP sticks. You can pair these with a 4-channel...
<SNIP> ... This is good to hear. I have no practical experience and have been reading up on forced induction, injection etc in preparation. In "Forced...
... I think you've hit the nail on the head, my recollection of AGB was that wasted spark was just fine. On a forced induction car you typically have little...
Will, Cheers for this very useful information, I'll print this off for future reference. I'll reply to your response by e-mail to keep things on-topic here...
its no problem with wasted spark on hi perf engines. here in sweden there
was several rallycross engines who ran with wasted spark, turbo, and much
overlap....
I have never seen a cam profile that would allow the intake to open while the piston was still coming up on the exhaust stroke, not to say there isn't one. In...
Hi I am new to the list :) Just thought i'd chime in mk3 supra turbos use wastespark i owned a couple. Anyone have the book maximum boost by corky bell? I...
Gonna guess that's the trigger wheel from an L28ET, which is what I am running ( one of many), the larger slot casues no adverse effect the trigger signal will...
Dave, Did you move the tach input from pin 24 to pin 25 like this diagram states to do? http://megasquirt.sourceforge.net/extra/pix/msns-lumenition.jpg I...
No, not quite, there is a complete write up on Hybridz.org by moby and I think he posted it on the msefi forum as well, where in he details installation on the...
I think you'll find most folks use the VR trigger from a ford Edis System. not magnets. 36-1 tooth steel trigger wheel and the sensor is all ya need. ... From:...
I am helping a group install MSnS on an '84 BMW 325e. We believe that everything is wired up properly, but are having trouble getting any spark. We are using 2...
Hi Philip, I have not played with the HEI yet so I can not give you any real troubleshooting input. But the look up power is to allow a full sweep of the ...
OK, awesome. This reinforces my understanding that I have developed since I sent that message. I think I have discovered the problem that I was having,...
I would recommend bypassing the relay board completely, I have found that it is a noise amplifier for crank signals. Thank you, Mike Lough LoCustom.com ... ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
