Hey I have been doing this MSnS thing for some time on my 16v VW turbo golf. It seems pretty good but still having some issues. Until I get our dyno set up I...
Kevin, I had a similair problem on my car and found the advance SAW signal was not working. It turned out I was running a fixed 8-10° ADV. Before I popped my...
That is a great page. I am looking at having to make a MAP/timing table from sratch soon too. ... http://us.click.yahoo.com/kEZsdA/bwnGAA/YiGOAA/0UzulB/TM ... ...
I think that SDS page recomends something like 28-38 max advance I would stick with something like 35° Oh, some guys have been playing with timing just before...
I was excited about that and boost control. But right now MSnExtra is just software for the MS. Knock sensing, boost control, etc. require piggyback...
Paul, Hey thanks for the prompt response. I believe that my advance mechinisms are working since it does make an extreme difference in engine smootheness when...
Cool - I am just putting the finishing touches on a new "equal(close)" length exhaust manifold. I haven't started the fab on the turbo out yet. I will be...
currently I am having issues getting my tuning computer to talk to a printer so I can at least study the maps. If when I do get it all working right, I will...
Oh hell I had a page bookmarked, that has 75 Lbers for 5-55 bucks but I had to format and reinstall... I will try to find the page again. If I am not mistaken...
I would like to see that map too. I am doing 4G63 with basically the same turbo as you, T4E 57 trim T3 turbine... and the engine displacement is nearly the ...
Yep, thats the one...hella good prices on injectors ain't it? ... ===== __________________________________ Do you Yahoo!? Yahoo! Mail - 50x more storage than...
Joe, working on new maps for ignition to improve resolution from 1300-3000 rpm. This should allow me to isolate issues in specific ranges. Let everyone know ...
well This is a general idea I was going to do... start with Base reading KPa. For every 10 KPa rise, add 1-1.5-2*. Then once I hit Bar, subtract 1-1.5* for ...
if edis only goes to 9000rpm then t sounds like not something that would be good to put on my fj1100 turbo drag bike-sherwood ... Do you Yahoo!? vote.yahoo.com...
Sounds good Joe. I built a map line at 100kpa. Then made ones lower and higher. Higher is easy. I was told rule of thumb 1*/2psi. The map I use has a ...
Hey do any of you guys have turbine or compressor maps for these T3, T4 Etc... I would like to compare what you guys are running to the IHI stuff me and few...
www.turbonetics.com has most Garret maps posted Neil ... T4 Etc... ... me and few others are running. ... maps we know what we are dealing with. ... If I get...
A good site (calculator) http://www.turbofast.com.au/turbomap.html Our specific maps (T4E) http://www.turbofast.com.au/FlowTO4E.html ... === message truncated...
Forgot... You will need specific air flow numbers from your engine... here are a few equations to mull over... Pressure ratio... 14.7(atmospheric pressure) +...
Is your Spouse cheating online? Do your kids visit porn sites? Are your Employees wasting company time surfing the internet? Would you like to know the...
Hi, I have a "leftover" V1 MS board with the old MPX 4115 Map sensor. No problem uploading MSS .s19 file, everything works - except I see map values at ambient...
Someone pointed me to a bunch of circuits for boost control, knock sensing, etc.. The other day and now I can't find them. Can someone point me to them? ... ...
... Signal to MS for knock control http://www3.sympatico.ca/borism/ http://www3.sympatico.ca/borism/Misc/MEGAKNOCK.JPG Signal to MS for knock logging ...
Re-finance now, even with bad-credit! *Best Re-finance Rate for credit challenged. *Best Customer Service *Lowest Interest-Rates in Years *SAVE $100-$400 per...
