Hello Allert, I tried to contact you on Sat, 26 Jun 2004, varied your email adress but haven't got any response! Please contact off list to ami8i ÄT gmx.at...
All I have a complete EDIS-8 including coils, module, timing wheel, pickup, and a complete V8 engine harness not just the pigtails. Asking US$225 for all. ...
http://www.garagerival.com/gallery/bmw325is_msns/gallery.htm <info and pics! all you e30 guys can thank me later! i'll start tuning tomorrow, the map sensor...
Thats bitchen. Glad to hear that it works. I have an 85 325e that I plan to convert soon. I will check out the link you included. Let us know how your tuning...
Yea I second that. I have a 944 Porsche which I am planning on installing the MS. I just don’t think my speedometer will work if I take of the Motronic...
I just drove the car around the block for the first time. The speedo DOES work with out motronic! the tach on the dash isn't working, so i'll find the diagram...
After going through a lot of good reading material presented to me by some of you about the siamese port-issue, as I'm dealing with on the Mini's A-series...
it is allways a problem. you know that 2 of the cylinders are always a bit leaner than the other 2, no matter what kind of fuel system you use, some manifolds...
1.) I can't see why 2 injectors would necessarily be any worse/better than 1. The position of the injectors relative to the flow of gas may have an impact. The...
James Overington
jameso@...
Jul 4, 2004 10:59 pm
3081
I respectfully disagree with Klas - Using 1 injector per port with an unmodified MS controller on the A series engine will give you problems for the reasons I...
i am not sure if it will give problems, i did not use MS on a multipoint (TPI) Mini. i only know for sure that i you change the cam in a MPI Mini without...
Hi siamese port guys, I asked before but I can't remember to read an answer. Why don't you make single manifolds and use single throttle bodies or make a...
You should have a look at Rover's patent related to the MPi Mini. You'll see why changing the cam which changes the overlap between the two cylinders in a port...
Thanks for your suggestion, but unfortunately the manifold/throttle body is not what is causing the problem. Two intake valves share the same port and open one...
Could you use port dividing tongues that go back far enough into the manifold to allow 1 injector per side.My guess is that the port would be too small, though...
... Thank you jimovonz, ... ...for explanation! Aha, there is only one hole in the cylinder head for 2 inlet valves. Really strange construction what engineers...
Ok, I hooked everything up. Im getting a blink on the ms board light (center led) and seems to be sending the signal right, but Im getting absolutly no spark...
Are you using a relay board? Make sure you have continuity from fidle to the db37 pin (can't remember which it is). You have to remove the fast idle relay and...
You know what! I DIDNT have that jumper in. I had it in b4, and forgot i had taken it out. As soon as i put it back in, it fired right up! Runin good now!...
All, I posted details of a modification I made to my MSD 6A to allow the mag. triger input section of the MSD to trigger the MSnS tach input and then following...
Check into Hotter heat range spark plugs. Common with turbo cars. Turbo cars come with cooler plugs than NA cars to reduce the possibility of detonation...
Heat range itself will not affect blowout. Gap will. Plug design can. Spark capacity (coil power) can. ... From: "awdaudi2000" <AWDAudi@...> To:...
Clare Snyder
clarence@...
Jul 7, 2004 6:54 pm
3102
Wiring is the same except for FIdle (pin 30) which should be connected to an ignition module (I use Bosch 0 227 100 139 from Saab 900) that sets off the spark...
24 and 30, plus some resistor changes to have MSnSpark. ... ===== __________________________________ Do you Yahoo!? New and Improved Yahoo! Mail - Send 10MB...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
