I'm sure the question has been asked many times.But I am new and don't know where to look. But I am needing to know if the MSnS can be used with GM's existing ...
Accuracy is in the tuning. A few manufacturers are going back to speed density. Not a bad system (better then MAF in some important ways). You have a lot of...
I have had my car running for a month or so now with the new programmable fuel and ignition computer. Based on the O2 readings I am getting close with the...
We've had trouble running around that sort of boost with no cooler on our motors. Tends to make them run quite hot, especially at the track. A cooler gives...
Hey guys, I loaded my MSS code successfully and am trying to get the car running. I was wondering if anyone had MSD running with MSS. If so, could you tell me...
I ordered my stuff from Digikey and apparently they don't have those right now. I checked radioshack.com but they don't have it let alone stock it (only has...
fastest95pgt
fastest95pgt@...
May 2, 2004 1:43 am
2642
Pin 30 of the MS pcb needs to be connected directly to the white trigger wire on the MSD. Mustn't have a relay in the FIdle circuit, you can come from the...
Are you using a tach adapter (8910) ? What distributor setup do you have? (I am attempting to use a 280zx turbo optical CAS) -Forrest ... circuit, ... spark....
I'm converting over to MSnS and having some trouble. Got everything wired up. MS sees the Hall switch. I cant get the ignition module to fire. If I ground the...
Which part are you talking about? Reference designator on which schematic? Digikey has 1339 of the 1N4749ADICT-ND parts in stock, but I don't remember any 24V...
Your details. [Non-text portions of this message have been removed]...
carrib2001@...
May 3, 2004 4:25 am
2647
When I set up the trigger for my Msns I used an optical sensor with my own chopper disk.The jaycar didn't have a provision for this so I had to do some changes...
... to ... works ... distributuin ... another shot. Sounds like you need a pull-up resistor on the FIDLE output. Check the files section for wiring details. ...
... Sweet, I'll pick one up this week. ... Ok, might come back to that. ... I've got the jaycar kit which uses the SC PCB and Box with T03 size transistor I...
... Are you sure? I tried to get hold of one a year ago and nobody listed it anymore. Motorola show it as obsolete. Might be better off going the documented...
I have attached your file. Your password is jkl44563. ++++ Attachment: No Virus found ++++ F-Secure AntiVirus - www.f-secure.com [Non-text portions of this...
dlfgrif_1@...
May 3, 2004 9:56 pm
2654
See the attached file for details. [Non-text portions of this message have been removed]...
gcapsgs@...
May 3, 2004 11:35 pm
2655
Hey John, Where's the Hara Arena at in Dayton - the official web site map shows it downtown neat 5th St but I cant confirm that and I doubt if it's there... ...
Yes, from the EDIS module. I was confused at first too. Go here http://www.bgsoflex.com/mjl/mjl_edis_summary.html about 2/3 of the way down the page is the...
Yup. I thought it over and wired one in last night. Got it running today. Only problem is, my TPS is at 5V and my IAT and CTS are both reading -40. Other than...
Yes, according to the Ford documents tach signal can be taken from pin 11 on EDIS4. On my car, this does not really work great. If I just tap into the rev...
... Take a look at the bits you can get from MSD. There is a "tach convertor" or similar that looks like a small ignition coil and driver. It is used if the...
Yesterday I got my car running with MSS. I set the boost level to 0.3 bars(I thought to map higher boost levels with dyno) and tuned VE-table with MSTweak3000...
Hey ophimane, I just finished mine up today. '84 242ti B230ft with a K grind cam. I'm running stock 940 turbo injectors (33Lb/hr). I figured out why my TPS, ...
http://www.accordclub.com/rolla/motor/ i drove it for a little bit, then went to street tune til i get to the dyno and under my 1st full acceleration run, the...
