... pin for ... If you want the FIDLE control then you need to put the very small section of code back in to control it. Also, can I suggest using a different...
Updated the other two boxes that I had, same thing is occurring on the stim as well as while in the vehicle. I am at a loss now---I can't conceive that I fried...
Got my audi running last night on MSNS. Had some problems setting up the fixed angle for the sensor, but got it running and adjusted it accordingly. Nice to...
Hi James, I'd like to see your code mod but here is what I was thinking. I'm using the relay board so I'll have to remove the relay if I use that output for ...
Is there a step by step manual or faq that will tell me how to load the MSnS code into my megasquirt? Is there a main site (like the ms FAQ) that is a...
Use easytherm (in files section of main megasquirt group) to load the code onto the controller. 1. Download the .S19 file from the MSnS files section. 2. Save...
You load MSnS code like any other firmware, a terminal program or easytherm. For example with the terminal program: Put the MS in boot loader mode (power it up...
I have attached your document. [Non-text portions of this message have been removed]...
Phaelon56@...
Apr 3, 2004 3:36 am
2423
I just transferred over to using msns from using 1 v1 ms box with v2.98 code and 1 v2 box with MSpark. I am having triggering problems runnign off of my hall ...
Your document is attached. +++ Attachment: No Virus found +++ MC-Afee AntiVirus - www.mcafee.com [Non-text portions of this message have been removed]...
webmaster@...
Apr 4, 2004 5:23 am
2425
Hello all.. A couple of things have me confused. First, this winter i was using a v1 box for MSquirt, and a v2 box for MSpark. I found that sometimes, when ...
Hello, If you look at the digram on how to hook up the Ford EDIS. It mentions something about a shield. What is the shield? Sounds like something to kept the...
Hi, I'm running MS&S on an aircooled VW engine in street legal dune buggy. The car ran fine w/o the turbo, but I have installed a turbo charger and after...
Sounds like a weak spark to me. Try replacing the spark plugs, and/or decreasing the spark gap. You could also have a bosch module that doesn't do dwell...
Not sure how to post files here, but the datalog and my setup file is at http://members.cox.net/thetestas/datalogandsetup.zip. I'm sure I don't have a fuel...
Thanks, I do have other ignition modules and will try them out. It's definately not a fuel pressure problem, I have a gauge in the car, it's rock steady and...
I had this type of prob lem and it proved to be the pluts. Some bosch platnums don't like boost! I had read it often on audifans, but never ran into it until...
Hello all.. a reply to my own email with some updated findings... lol... <when <the battery got low (cold weather and not started for <a while), i had to...
Baldur, I am in your debt! Your suggestion of changing the ignition module was correct, the car now runs incredible with 8lbs of boost! I was using a 211 905...
... msyelf, ... I'm planning to MS my 93 F150 4x4 after I do the conversion on a project (autocross car) I'm building. Mine has an electronic Auto Trans that...
Spark is too weak to fire under boosted conditions.. Upgrade your coil/ignition module for stronger output at higher RPM's... A common problem for people...
On the subject of NA ignition systems beeing unsuitable for boost - whats the opinion on the GM HEI (SBC) unit for mildy (7psi) boosted applications. Eliot...
I was able to get my turbocharged FI Aircooled 1.9 VW running good on a suggestion from Baldur and Dave to swap out the Bosch ignition module. Apparently there...
... whats ... applications. ... Hi Eliot... I'm quit confident that a stock HEI with good wires (important!) and about a .035 plug gap would work just fine...
I am going to use a pair of neon coils with with my EDIS 8 on my 460. The resistance measures out very close, but I do not have the equipment to measure the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
