Don't know how easy or difficult this is, but is it possible to make Megatune SS so I can alter both spark and fuelling, then I only need to use one bit of...
... David, Not right now, but... That's the current development direction of MegaTune. I'll be starting the code to make the 3d tuning page into a generic...
... Tricky question - here's some more thoughts For MSnS: In many original dizzy installs, the distributor also drives the oil pump so you would have to retain...
Hi - I am looking for a spark table to start with on my Toyota 4A turbo w/MSnEDIS. If someone is willing to share what they have it would be appreciated. A...
Well, not quite a table, but someone who has tuned a lot of Link computers over here runs 20 degrees max on boosted 4AGE's. Even up to 30lbs. With the std...
I have been doing some thinking on the best way to control multiple EDIS modules with MSnEDIS (e.g. 2x EDIS4 for V8, 2x EDIS6 for V12) and thought I'd post my...
The Palm MSS tuning software has been uploaded to the Files section /Magnus ... From: Philip [mailto:daxtojeiro@...] Sent: den 30 januari 2004 16:48 ...
... Robert, download the MegatuneSS manual in the files section (files- software pc-MegatuneSS Manual) I believe it will answer your question. Brad J....
Thanks for your response. I was running SDS w/coilpacks last year, so while I have a dizzy setup, it's not in the car. Implement spark-cut? (rev-limter? launch...
... setup, it's ... Yes, because the EDIS module controls the actual sparking there is no way for the MSnEDIS to tell it not to spark (unless an external relay...
Just wondered if anyone had noticed a lack of spark energy at higher rpm with richer fuel mixtures with the stock VW ignition module that seems to be...
Maybe you could interrupt the ground circuit to the coils if you want spark cut. Just a thought. Jim Blackwood Blackwood Labs 9406 Gunpowder Rd. Florence, Ky...
Good point 8000rpm max but with high compression and rich mixtures <its a 4cyl> I know VW never designed the engines they were using the module with to rev...
Am in the process of testing to see if MSnS will work on the racebike I am building. Have run MS in the past on one bike, and am presently running MSpark on...
Hi Brent! Actually I think the timing jitter is because interrupt for spark T2SC1 occurs while interrupt for T2SC0 is being executed. I did consider having ...
... racebike I am ... [big snip] Very interesting observations there. If you are prepared to rework the code and hardware a bit, you _could_ run the injectors...
I'd be suprised if Bosch didn't engineer them with a little extra. I guess there is one way to find out eh? :) Jerome moonsteel@... "Spoilers up!" ... ...
I'm in the process of building a couple Megasquirts and I would really like to assemble them to allow a future add of EDIS without opening up and changing the...
There is an awful lot happening in the TIMERROLL code. Am going to look at moving some of this code out into LOOPER and just set flags in TIMERROLL. Will also...
There is already a timer being used for the spark, correct? T2SC1 is the interrupt being serviced by SPARKTIME, which has very little code before turning on...
Have somebody tried to solve any of the problems? The only thing i need now is a working 2-step rev limiter, just to build up turbo boost at the start line... ...
Would explain the behavior. Goes pretty random. Was going to look into a single trigger on crank, and the 90degree delay, but that would mean that it would be...
Dave, I've datalogged 7800rpms on my 2.0 8v while in the burnout box, and it started cutting out about then. Not even 100% sure it was an ignition cut, maybe...
