Excellent, many thanks. Cheers, Brian ... From: Marcus Saw To: zx7rr@yahoogroups.com ; mc-engine@yahoogroups.com Sent: Friday, April 29, 2005 7:59 PM Subject:...
... Stupid question -- are you talking about a KTM two-stroke (250 SX, 250 EXC) or four-stroke (250 EXC Racing)? I can't imagine KTM's figured out how to make...
Andrew, This is the 4-stroke, and you have to understand that the factories aren't maxing out these designs, jut making reasonable power with them. The RR ...
Rui, If you are looking mainly for watercooling you could do as was done on two-stroke air-cooled cylinders in the past and trim the middle fins back and weld...
Several of the CB160 racers at the AHRMA national this last weekend had NGK plugs break. One was the side electrode coming off where it is welded to the body....
... Ahh, IC Forensics! I was absent from college on the day they studied this. I was also absent from college on all other days, but that's beside the point. ...
I've heard of severe detonation breaking plugs along with of course the destruction of the other engine components. Even moderate detonation will severely...
David Kath
BSAGS@...
May 3, 2005 8:11 pm
8616
... Dunno about this, but I once had the misfortune to try and save a few cents with Champion brand spark plugs. The ceramic broke in half, the top stayed...
Seriuosly considering building a water brake dyno for roughly 100 HP...anyone got a good source of info for details??? Like how to set up rotor and stator??...
... Wasn't there a thread on building same out of a big V8 automatic trans troque convertor a ( long ) while back ? Cheers IAN...
D.M.Co.
iwd@...
May 5, 2005 12:13 am
8620
Wasn't there a thread on building same out of a big V8 automatic trans troque convertor a ( long ) while back ? Hey Ian.....that must have been before my time...
... That was discussed too from memory. As you are looking at keeping costs down ( to zero ?? ), run some soluble oil in water, should not do too much harm....
D.M.Co.
iwd@...
May 5, 2005 4:45 am
8622
I have just had this suggested for my race MV single engine.. I am taking the bore from 59.5 to 70 and I was going to use a cast iron liner as we discussed...
... ...then "michael" wrote: I used to think that, until I realised that Brit boxes were doubly indirect in the lower gears. Yes they were, I'd considered...
In a message dated 5/5/2005 3:42:55 AM Pacific Daylight Time, ... ______________________________________________________ I used to think that, until I realised...
GStarRon@...
May 5, 2005 2:51 pm
8627
... Do you want to point our fellow lister to the archive then ? ( Does Les still have it up ? ) Cheers IAN -- DRYSDALE MOTORCYCLE CO. AUSTRALIA PH: +613...
Ian
iwd@...
May 5, 2005 3:34 pm
8628
Tony talked on the chassis list about making a dyno from an automatic transmission/torque convertor. cheers, Michael Hi Michael...do you recall if it was...
... Stick with the cast iron unless you like heart break and empty pockets. Cheers IAN -- DRYSDALE MOTORCYCLE CO. AUSTRALIA PH: +613 9562 4260 FAX: +613...
Ian
iwd@...
May 5, 2005 3:47 pm
8630
From Tony Foale's post: I have Carl Shipman's engine tuning book which uses a water pump as the brake unit. My homemade dyno is at...
I have Carl Shipman's engine tuning book which uses a water pump as the brake unit. My homemade dyno is at http://pages.quicksilver.net.nz/geoffm/. I will have...
... Goto http://pages.quicksilver.net.nz/geoffm/dyno/dyno.htm and get http://pages.quicksilver.net.nz/geoffm/dyno/dyno_article.zip and all will be revealed ...
Buy a used dyno wherever you can find one or order a new one from Stuska. http://www.stuska.com/ The reaction unit itself is a bargain and the rest you can...
Buy a used dyno wherever you can find one or order a new one from Stuska. http://www.stuska.com/ The reaction unit itself is a bargain and the rest you can...
... <BR> ... <BR> ... Goto http://pages.quicksilver.net.nz/geoffm/dyno/dyno.htm and get http://pages.quicksilver.net.nz/geoffm/dyno/dyno_article.zip and all ...
Bob, I have a 400hp single reaction unit I am not currently using with about an hour on it if you want to save a bit of $. I also have a nice universal ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
