"Even on air cooled motors, 10sec WOT is not that bad. On a 4T you at least have a revolution to cool it" Yeah,I didn't phrase that right...what I meant was 10...
500 engines 1000cc 500hp cvt transmission hahahahah, not a hope in hell ... From: Julian Bond [mailto:julian_bond@...] Sent: 01 November 2004 11:51 ...
Went to a get-together organised by the local BSA club last night. One bloke had what was labelled as "Weslake head for B44". I picked this up and flipped it...
I figured we would be talking about RC motorcycles Take a look at the 1/5 scale Honda RC211V http://www.internet-rc.com/15scalnitpow.html I have seen these...
In a message dated 11/1/2004 3:57:51 AM Pacific Standard Time, ... Well, I used to run a drag racer 2 stroke, redline at 15,500 rpm's, took me just over 10...
GStarRon@...
Nov 1, 2004 3:49 pm
7820
... For Honda 350s, Todd Henning (right name? x-usa vintage racer who had terrible accident several years back) got some development help from an engine guru,...
... Back in the early eighties, my buddy built a Yamaha RD350 drag bike that ran 3/10 second off the (at that time) national record. He said, it was fun ...
"Last I heard, Todd (or someone) still sold the kits and/or the separate parts. The pistons were beautiful little pieces, oversized and perfectly-matched to...
Online instant messager chatting center for motorcycle rider in your area! Free to browse motorcycle fans in your area! Dating center for bikers and admires in...
Hi! I would like to welcome you to my new website http://jkmachining.ca/ in hope to call for the interest from the riders who is looking for quality CNC...
... Rather hard to believe anyone would CNC a clutch lever. (per pictures from the website) Good thing he didn't join this list solely for commerce! jrc...
CRG does a brisk business doing just that. Regards, Derek motolab http://www.moto-lab.com <http://www.moto-lab.com/> ... From: Ray and Sonja Crenshaw...
<>I've been attempting to finish off modification of a Goldie crank for a mate who had taken it back from someone who was taking far too long (3 years!) to...
Online instant messager chatting center for bikers in your area! Free to browse Honda motorcycle fans in your area! Dating center for bikers and admires in...
I have a 500ss norton head which has started leaking oil under the bridge of the rocker cover.It would appear that the aluminium is porous. we have welded were...
I'm not sure what Threebond 1104 is, or how suitable it is. Owners of early american bikes swear by the use of something called glyptal, which is a sealer for...
RohanB
rohan3333@...
Nov 6, 2004 11:02 am
7831
Thanks for your input Rohan, the head has always weeped oil since ive had it, I suspect after i had the exhaust ports welded so they could be "D" shaped that ...
... You were warned it would be a thankless job............ You need a little jig grinder - usually air operated little beauties that fit in boring heads. As...
Ian
iwd@...
Nov 7, 2004 12:44 pm
7833
Greetings, everyone! I would like to pose a hypothetical question to everyone in the motorcycle engine group. If you were an engine designer and you were...
Don't think this is really an issue, since Buell does not exist anymore. Being a wholly-owned subsidiary of Harley, I imagine they will be required to use a...
Online instant messager chatting center for motorcycle riders in your area! Free to browse motorcycle fans in your area! Dating center for bikers and admires...
Thanks Ian, After hearing of my plight a mate came up with the same advice ..... and the loan of his jig grinder. The hole is finished and I will continue with...
... In the interim, a set of air-cooled, 4-valve (that is, 4-per-chamber) pushrod heads for the existing H-D bottom end. Then it could also fit the other H-D...
... The Harley system (at least pre-evo) relies on scraping the crank OD to deliver oil into a pocket for the timed breather to get it out of the crankcase. ...
... although they vary somewhat on the heat treatment advice, one says 30 thou and the other says 40. ... The INA bearing book talks about calculating the...
Hopefully this will go directly to the page that has the detailed instructions on how to use the TwinMax carb balancer. Should work just fine for the...
... Since Hesketh, Britten, Aprilia, Ducati, Morini, Honda, Kawasaki, Suzuki, Yamaha, and others all did V-twins, I'd do anything *except* a V twin... ... I...
Hi Dave, ... Buell bought the Barton engine and rights to make it, though from what I've read he had to pretty much re-engineer the whole thing. Too bad that...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
