Hello again everyone. Since I'm on Spring Break this week, I thought I'd give you some updates on the restoration of the car. I haven't been able to do much,...
Dear David, I found this in a pile of items that were my fathers. Thought that you would like it. Thank care, Megan Simmons (Joe and Sheila's daughter) ... ...
I'm looking for tips on how to reduce the oil leakage from the interior of the transmission drive shaft out past the plug. Right now, the best I can figure is...
Chuck Several of us who own 2-cyl. cars us RTV on the plug threads; enough to fill the splits in the hollow shaft. BJ Coombes 1909-LD in Oregon ... From: Chuck...
What Plug? Jim Dix Big Flats, NY West of Pluto ... From: Chuck Richardson To: maxwellbriscoeowners@yahoogroups.com Sent: Monday, March 23, 2009 2:14 PM ...
I understand that. It's just that I feel a little like Hansel and Gretel, except I'm leaving a trail of oil drops from my house to where ever I visit. I did...
Chuck, I think it's the general nature of the beast. I've generally approached it that if it isn't dripping oil over the place then something's not getting ...
David, I recently re-ringed a 1 cylinder 1907 REO with new 1/4" wide piston rings but when I took the chassis to an excellent California restorer to 'breathe...
Hi Megan, Thanks for that. Regards, David McCredie _____ From: maxwellbriscoeowners@yahoogroups.com [mailto:maxwellbriscoeowners@yahoogroups.com] On Behalf Of...
I only get about 20 degrees of spark advance on my Splitdorf H and the linkage to the steering wheel. Is this standard? I run the car off of a battery, using...
Chuck I asked myself exactly the same question the other week. I advanced the timing one tooth to see what happens if I used more advance. I then ran the car...
Hi, I just posted a picture of an insulator I'm needing, especially the male part. Pls let me know if you have one or two I can buy. Thanks Dave in Wichita...
Hi Merle, what is the price on the Splitdorf Coil and magnetos and will it work on a 1912 2 cylinder? Are they in working condition? Thanks Bill Lorenzen Dir....
Hi, I found a page in an old 1918 manual and have posted it in the photo section under Maxwell carb - enjoy ! You may have to zoom in to read it. Dave in...
Bill- The coil and Mag are both rebuilt and correct for the 2 cyl '12AC. The coil is $950 and the Mag $875 or both for $1750. I can send you pictures if you...
Hi. Does anyone have a spare tool box for a model AB? If not, could someone please check some drawings I have made to make sure that the dimensions are correct...
I am losing pedal on my Mascotte's clutch. I am assuming this clutch is similar to Model I and perhaps Q clutches. It appears as if there is an adjusting nut...
I finally recieved the new timing and crank gears from Lab Threads, they did a great job, fit right into place. The hard part was setting the cam timing using...
For my 1911 Model I I need a couple of tubes, one wheel runs flat every so often, and I have the impression that repairing the tube is not the right thing to...
Tony, 32" X 3 1/2" is a 25 inch tire. Just multiply the 3 1/2 by 2 = 7. Subtract 7 from 32 = 25. You need a 25" tube and tire flap. I use 33 X 4 tires on my...
Hi Tony, I also own a 1911 Model I. Your tires, 32x3 1/2 (25" wheels) are just a smaller profile of the 33x4 like I run on my car (25" wheels). So what you...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
