Hello all. Recently my father and I have begun to work on the 1910 Q3 Touring car that he and his father and uncle pulled from a collapsed barn in the early...
Greg......I can't speak about specifically about the Q3...but on my 1908 K, 1909 DA & 1910 E the frame is the same as the body color and the fenders are black....
Greg: We have a couple of dozen Maxwell Q's listed in the Registry. I am sure that many of these owners are willing to share whatever information they have on...
Vern Campbell
dvcampbell@...
Mar 10, 2008 2:29 pm
738
I am working on the completion of my '06 Runabout, serial L1460, 2 cyl. I will be making the brake rods but lack a pair of clevises used at the top of the...
In the classified ads of the Horseless Carriage Club web site (hcca.org) there are a 1910 2-cylinder and a 1914 40-horsepower Maxwell for sale in New Jersey....
Can you tell me about the 1910 2-cylinder, I was interested in buying it. Father Sanford Sears, New Bern, NC Gil Fitzhugh <oldcarfudd@...> wrote: In the...
Sorry, while I know the people, I'm not familiar with those particular cars. I normally see them on tour with a 2-cylinder Buick or a 1911 Cadillac - which, I...
On my dad's 1911 AB the lid or cover under the driver's seat that is over the battery has a label on it that starts out: IMPORTANT NOTICE TO THE PURCHASER OF...
Rick: I have that label on my car, and I have re-produced it on the computer. Give me your name and address, and I will send you one. Vern Campbell ... From:...
Vern Campbell
dvcampbell@...
Mar 25, 2008 1:19 pm
744
Courtesy of Bobby Warren: TO THE PURCHASER OF THIS AUTOMOBILE 1. Whether you purchased this car new or second hand, notify the Company immediately, sending...
Our Maxwell AC has just arrived & its even better than expected. It has been fully restored but not started. Everything is ready to go except that the 2...
Congrats David, I can tell you that if the car's ignition is truly stock: DO NOT use 12 volts on the dashboard mounted Splitdorf coil it will burn out! It...
. . .. at last week's Chickasha swap meet !! After over 25 years of touring with a real nice Rubes single twist suitable for a '13 Model T, I traded for - what...
Hi George, I have a 1913 T that I have owned for 60 years. I bought it from the original owner. The horn is a single twist Rubes style, no name, mounted...
Hi Tom & the group, I don't wish in any way?to dampe Tom's?glee at finding that hard sought after?part. I can relate; after all, after 25 years of looking I...
The horn picture is a picture of the horn on my 1910 AA. A couple years ago at Hershey, Merle Simonsma came by and I asked what Maxwell goodies he had found....
Howdy Tom, BJ and the Group, I meant to say that I finally found a Maxwell-type horn for my '10 AA so I can take the incorrect '13 Ford horn off. Its adorned...
Thanks for the all the advice received regarding the ignition system on my "new" Maxwell AC. I got it started it today on "Battery" after correcting some...
David, Glad you got the coil wiring sorted out. I never did find my wiring diagram.?The coil sounds like a new motorcycle type (BMW for example)?and would be...
Thanks for that, when I started it, I only ran it for a few seconds because it was getting late and I could not see the oil sight glasses but when I switched...
Have just posted 2 photos of the starter/generator fitted to my 1912 Maxwell AC, as requested . It has been very well done, by removing the four large stud...
David, I don't have an authorial answer on the mxRPM of a Maxwell engine; but I am sure I have had mine over 1500 RPM --for short times while running down...
The starter generator unit is a Delco Remy Model : 1101970 Serial # 4M29, Delco Remy in their reply referred to it as Follows: "According to a 1977 Model...
Rick, I have an entire fully elliptic spring I'd sell. It has the clamps that crimp over both the front and back. I forgot if its 4 or 5 leaves (back or...
Rick......Benz Spring in Portland, Or. will make new springs if you have a pattern. Talk to Bill Benz only....other people there aren't sympathetic to helping...
I have a few questions regarding our Messenger: The screw cap on the oil tank has a small hole (~1/16") drilled in it. Can anyone tell me if this is original...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
