Whilst I'm no expert on Briscoes that originate in Brockville, Ontario, Canada, the information I have would tend to suggest that the Briscoe you have is not a...
Can anyone tell me the diffrence ,from Model A and AB Maxwell cars circa 1908 , l know model A only ran for some 500 cars as it was not success ,l think my...
HI All, There was a Maxwell A and an A Junior in 1909. The Junior was an economy model. The AA was a designated Model for 1910, the AB model was the...
Yesterday we brought home our "new" 1912 Maxwell Special touring. I posted a couple pictures in the Photos section. Does anyone know where the serial number...
... like. ... the front seat base, left hand side of the driver's seat, or right hand frame horn. My 11 Model I has the number on the right end of the front ...
Brad....on the 1908, 09 & 10 four cylinder cars the serial number is located on the top of the alum. engine block, right side, front - often under the bracked...
If anyone knows of someone looking for a 19120 Model E Maxwell 4 cylinder touring car is great touring condition, have them contact me. I am considering...
The only number I found was stamped into the top of the front seat riser under the cusion on the left side. It looks like 2238. Is this the serial number or a...
I finally found the number! I looked up another guy in the HCCA directory that had a 1912 Special and he told me where to look. It would have taken me weeks to...
Brad, What's the number? Jim Dix ... From: Bradley Wallace To: maxwellbriscoeowners@yahoogroups.com Sent: Tuesday, February 05, 2008 10:08 PM Subject:...
The number is 7411. However, the ID plate that was attached to the lower center dash board would have had the number 87411. The plate is missing, but there...
Hello Brad: Congratulations on the purchase of the Maxwell. I keep the Maxwell Registry, and I would like to update it to include you and your car. We have...
Vern Campbell
dvcampbell@...
Feb 7, 2008 5:02 pm
720
Did you all see the 1908 Maxwell LC Runabout on e-bay for sale E-bay # 150213278053 Earl Brown Lake Tapps, WA....
Thank you Vern, This car came from your neighborhood. It's the one that Guy was selling for RM. It came from Texas and I beleive it may one that wasn't known...
Hello Brad: Score. The car you have, we have listed under RM auctions. The numbers match 87411. I had talked with the good folks at RM, and I recall the car...
Vern Campbell
dvcampbell@...
Feb 8, 2008 3:12 am
723
I am in the middle of installing a top on my 1910 AA. I do not have any original pieces but want something that looks right. Also bearing in mind that Maxwell...
The first attached photo (it's on ebay right now) shows the loops mounted to the front face of the bow on what appears to be an AB, although somewhat more...
I have what I believe to be an original AB top. The straps are mounted on the front face of the front bow, atop the welting. I don't have photos, but can...
The good news is that I got to drive my 1912 Maxwell Special for the first time today. The bad news is that a hole opened up in the water manifold that's big ...
Brad: I do not know of any reproductions on the manifold. But that is aluminum, and it can be welded. Make sure you take it to someone who knows what he is...
Vern Campbell
dvcampbell@...
Feb 19, 2008 3:59 am
728
Brad.....getting new ones made is not difficult, only expensive. I have three of those cars and could use a couple of manifolds so this would be a worthwhile...
I would be interested in having another water manifold for my 1911 Model I. Let me know what the approximate charges would be. Bob Ricewasser Richard Anderson...
I think the first step.....if we are going to start a new water manifold project....is to be sure we all have the same size manifolds. Can people take...
Measuring from center of port 1 to center of port 4: 19" Measuring full length: 25 3/4" Measuring width of flange: 3 3/4" By the way... I'm hoping mine can be...
Brad...and anyone else.....let me know if you are serious about casting new water manifolds. The more we cast off of the mold the less expensive each one will...
Brad...and anyone else.....let me know if you are serious about casting new water manifolds. The more we cast off of the mold the less expensive each one will...
This is my first post as a new member of this group, awaiting the arrival of our Maxwell AC due in Australia in a few weeks. We just returned from a car rally...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
