I still have a few of the advertising signs and Maxwell service shield signs left that I reproduced for the 2004 Maxwell Centennial tour in New Castle, IN....
Reminder from: maxwellbriscoeowners Yahoo! Group http://groups.yahoo.com/group/maxwellbriscoeowners/cal Brass in Bucks Flea Market Sunday May 20, 2007 All Day ...
maxwellbriscoeowners@...
May 15, 2007 4:00 am
605
________________________________ From: Bill Lorenzen Sent: Friday, June 08, 2007 2:45 PM To: 'maxwellbriscoowners@yahoogroups.com' Subject: Information Needed ...
Bill, I use 30 W detergent oil in the transmission and brass firewall reservoir for my '10 AA. I think I use 90 W - 120 W in the rear end. Good luck on...
Hi Bill, In my experience, the grade of engine oil doesn't make a whole lot of difference. How much your car throws out and drips might influence your...
Bill....On the west coast we tend to use 20-50 oil in our engines and drip tank. Viscosity has better hang time. Trans. and rear ends get the same - 90 W.Rich...
Iam BJ Coombes of Eagle point , OR. I have a 1909 LD Maxwell. ________________________________________________________________________ AOL now offers free...
Thanks Chuck I see you live in Altadena, CA. I was born and raised there, north of NY drive in a subdivision of the old Allen family's Sphinx Ranch. Go...
To All: I have been thinking of doing my Christmas shopping early this year (a first for me), and have contacted a local goldsmith about making a tie...
Hello BJ: Thanks for making contact with the Maxwell network. I keep the Maxwell Registry, and we have a Robert L. Coombs listed at 4733 Oakwood Ave., La ...
Vern Campbell
dvcampbell@...
Jun 12, 2007 2:21 pm
614
Looking for the red paint formula for a 1908 Maxwell LC. If available, please specify the paint manufacture and paint type. Any information would be greatly...
Hi. LC's are one of the rare small 2 cyls that can be green as well as red. My LC I painted green, years ago, but the incorrect shade. Vern Campbell has a...
... Thanks for the information. We've been debating the color but are leaning toward red with gold pinstripe, as that was the original color. thanks again jva...
G'day from downunder, I have finally got my '09 Model A on the road . . but we seem to have an exceptional amount of oil leaking out. I was told that Maxwell...
I'm looking for brake drums for the Alice Ramsey 1909 Model DA Maxwell. Does anyone know where I might find a pair. They are 11 1/2" ID. I also need one...
If everyone is still interested, I've asked for the same time at Hershey in the HCCA tent this year as last, Thursday at 3 PM. A "hat" will be passed to offset...
Hi Jim, Thanks for including me. It was nice to see you at the tour. If this is a go for the meeting, I will put a sign at our Hershey stand. Lud ... From: JIm...
lgocek@...
Aug 26, 2007 5:17 pm
621
Sounds good, I'll be there.Rich Anderson 206-240-9434To: maxwellbriscoeowners@...: jdix6@...: Sun, 26 Aug 2007 14:01:19...
Sounds great. Was not able to attend last year, but will make sure this year. Michael JIm Dix <jdix6@...> wrote: If everyone is still interested, I've...
Last Sunday my 1911 Model I ( 4 cylinder ) started to sputter and had a hard time to stay alive. On Monday I started to dismantle the Splitdorf magneto. It...
Hello Tony: Replacing the tungsten tip on the points is an easy job. The originals were soldered in place, and the heat will no problem. I do not know if the...
Vern Campbell
dvcampbell@...
Aug 31, 2007 3:54 am
625
Hi Vern, Thank you for your clear explanation. I wll first check with local suppliers for the tungsten points, and if necessay I will come back to you. Tony. ...
Hi Vern, today I managed to recuperate some points from a couple of regular sets, and I turned a litle point on them on my lathe. Soldering them on was no real...
Vern, I have always silver soldered the points on my vibrator. Your comment sounded like you soft soldered the points on mags is that true? Comments?...
Hello Leroy: Yes, I use nothing more than conventional solder on the points. I am sure that is what the original was, since a soldering iron melts it with ...
Vern Campbell
dvcampbell@...
Sep 1, 2007 3:05 am
629
Jim, Michael Bernard again. Just wanted to know if we were allowed to bring Maxwell stuff to sell at the meet. Was not there last year and I remember talk...
Mike, I don't know if it's appropriate to sell parts at the HCCA tent, I would guess not. If you were to say you have parts available and set up a meeting...
I would have thought that it would be ok to sell or swap parts at the meeting , or at least be given the chance to tell the fellow owners what you have for...
I'm sure you can announce what you have available and where it is. I don't think it's appropriate to drag a bunch of stuff into the HCCA tent and go about...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
