Sorry can't help Joe Chuck Richardson <chuckier@...> wrote: I need to rearch the front and rear body springs on my '11 AB. Does anyone know what the ...
Hello, I am Diving into the AA fuel system and I want to replace the cute but quirky Maxwell carb with a Kohler unit, I am in the process of fabricating a...
Hello John: The Maxwell carb is a bit quirky, but if restored to original specifications it will operate just fine. In fact it will be better than some of the...
Vern Campbell
dvcampbell@...
Jun 29, 2006 1:41 pm
422
John, I second what Vern said !! Whats more I highly recommend his restoration services. He assisted me in transitioning from a Wico John Deere mag to the...
Enter your vote today! A new poll has been created for the maxwellbriscoeowners group: I am using a: o Standard Maxwell Carb o Other non Maxwell Carb To vote,...
maxwellbriscoeowners@...
Jun 29, 2006 5:05 pm
425
And, I'll add my second - when he finished it was better than new....
Dear J0hn : I have had good results with Zenith side draft model 1408 you do not need to make up any special adaptor to the stock manifold. the centers on...
We use the Onan carb 146-0456 on six of our two cylinder Maxwells. Jim Moe did the throttle modifications. I still have two of the cars so I tried to vote...
Joe...I believe I paid $275 for it and only used it for about 100 miles. I had it on a big-2 cyl Maxwell and it didn't perform .....its really made for a...
Hello, Now, my next problem. I apparently have a flywheel that is starting to loosen up. It only has what looks to be a tapered key. The key moves within the...
Hi John, I have dealt exhaustively with this problem in my column in the May-June 2005 ANTIQUE AUTOMOBILE magazine. If you cannot find a copy, I will email...
-John, I would take the flywheel off and inspect the condition of the keyway slot on both the flywheel and crankshaft. Check the condition of the the keyway...
Hello John: You do need to fix that loose flywheel before you run the engine. You are right - it could lead to the kind of excitement you would not enjoy! Do...
Vern Campbell
dvcampbell@...
Jul 8, 2006 6:15 pm
436
Hello: We do not have this car listed in the Registry. Anyone know who owns it? Vern Campbell ... From: maxwellbriscoeowners@yahoogroups.com ...
Vern Campbell
dvcampbell@...
Jul 8, 2006 6:46 pm
437
Hello, I just want to thank every one for taking the time to get back to me, I have been a member of AACA for nearly 20 years and like so many others I cannot...
Anybody have any information or suggestions on cleaning that battleship linoleum on the floorboards and running boards? I'm reluctant to just dump plain soap...
Hi Terry, You can't hurt it with soap or detergent. Scrub as hard as you have to. When the marks are removed, coat it with Simonize paste wax. Tom Reese ...
Thanks for that info. Some $%^&* judge stuck his greasy hands on it after he crawled around underneath the car. I was afraid the fingerprints were going to be...
Hi Terry, Your car was greasy underneath. Can't be a Maxwell. :-) Tom Reese On Jul 24, 2006, at 7:09 PM, Terry Huston wrote: Thanks for that info. Some...
If you get a few coats of wax on it, it will clean a lot easier. I use old fashion paste wax for floors that I got at Lowe's or? When I got the car it was...
Terry: Like with Tom I have found that soap and water works just fine to clean up that battleship linoleum. Vern Campbell ... From:...
Vern Campbell
dvcampbell@...
Jul 25, 2006 10:11 pm
444
While pulling my motor, I noticed some endplay on the crankshaft. It measures 37 thousands, which seems like a lot to me. What would a recommended tolerance...
Hello Chuck: The end play should not be more than .002 to .003. It is determined by the shoulder on the main bushings, and the thickness of the gasket on the...
Vern Campbell
dvcampbell@...
Jul 26, 2006 1:05 am
446
Terry...I've had a lot of luck with a product called "Simple Green"..... Rich Anderson 206-240-9434...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
