Well Roger Gault his wife and friends from Grandbury, TX paid a visit to Bedford, TX yesterday to meet myself, my wife Toni and of course my Avenger GT12X....
Maybe 3! Michael Rockwall, Texas ... ____________________________________________________________________________________ Take the Internet to Go: Yahoo!Go...
And a fun ride it was. Given by a nice fellow. Man, that car is as pretty in person as in the pictures. Now, if I can get my bored and stroked 3.6L Corvair...
What are the odds, two yellow Avenger GT-15s here in Texas. Would make a nice picture with my red Avenger GT12X in the middle. Best of luck on your projects...
Well, I finally almost finished my Gulf paint Job.I still need to do the jambs and put the stripe on the trap door but overall I am fairly happy with it(orange...
Joe Do you have enough volume coming out of your compressor/ @yahoogroups.com [mailto:loflyin40@yahoogroups.com]On Behalf Of gideonarch Sent: Monday, July 02,...
Kevin, I am not sure exact spec.I am using my uncles compressor it is 3 phase I believe 15 horse with 80 or 100 gal tank(he had his own shop in Fla).The worst...
Joe the hundred feet of line may be killing you. Make sure it's 3/8 id or larger would be better. Also wind the guage wide open at the gun, go back to the...
I am in the middle of lowering the floors so I can install some comfortable seats and still have some headroom. After looking at the stock floors and fiberfab...
Wayne I'd like to see a picture when your done. I am trying to comprehend this and I can't seem to. All the seats I found were to wide to fit between the...
... comprehend this and I can't seem to. All the seats I found were to wide to fit between the fiberfab rails and the hump in the middle. 18" seems to be the...
Mike I have honda prelude seats and had to remove the adjusters and do a lot of cutting. Kevin ... From: mike mann To: loflyin40@yahoogroups.com Sent: Monday,...
When I lowered my floor pan I used 2x3 box tubing. I never had the original fiberfab rails so I simply made a box frame and went under the center hump forward...
Of course, another option is to raise the roof. There was a very nice looking yellow/black Avenger at Carlisle in '06 that had the rear end raised. "Ground...
Wayne, I just picked up (Saturday) a pair of Miata leather seats for my project. Look narrow enough to fit (19"). Height also looks good. Also have the tracks...
The yellow and black car was mine. We were determined to make the car a daily driver so we spaced the body up at the rear mounts and left in the front original...
Hi guys, I have a question/problem with my avenger carb.I have an old Solex pict3 on 1979 engine w/87mm pistons/jugs and 009 Bosch mech. advance.I recently...
I think you can buy a bushing kit and new butterfly screws for your old carb. If you do that, don't forget to "stake" the new butterfly screws to prevent them...
Sounds like it is starving for fuel. When you did the rebuild did you make sure all the low speed jets and air bleeds were clear? I had a similar problem and...
I posted a pic of the frame mods I made. I now have almost a 22" wide seat area. I made a box out of 2x2 and made cuts in the pan and fiberfab frame rails then...
Well I bought it off ebay.It had some varnish in the bowl when i took it apart my guess is they tested it at the factory and did not drain it completely.The...
Does your carb have the idle solenoid? Early models don't (I think - hard to remember that far back) but the later models do and if it is not connected or not...
Thanks for all the help guys.With your help I think I solved the problem.It was (drum roll please) the electromagnetic cut off switch.I never hooked up the...
Hi Guys, I have a question for all the avenger owners out there.With the low clearance between the throat of the standard vw carb and the rear deck does anyone...
Joe What about a air intake like the kids run on th tuners? A peice of pipe fitted to the carb run out into the wheelhouse and put a K&N on it. If you open up...
