while working on my trans for my Valkyri, I didn't like what I was feeling. I removed the shaft and was going to double check the instalation per fiberfabs...
If the needle bearing are in that bad a condition then the surfaces that they run on are probably damaged too. There can be only one layer of rollers in a...
Hi Daryl - I'll get out my Corvair manual in the morning and look up your answer. In the meantime the Best source of Corvair parts of all kinds that I have...
Hi again Daryl - Looking in my Corvair Chassis Manual and assuming you are working on a 4 speed transmission, not a 3 speed, there are two rows of needle...
The adapter is not that difficult to copy, the flywheel is the tough part. I have even considered redrilling a Audi flywheel but the area around the holes...
I expect their reply was from experience in seeing compressors running on long expension cords, wrong plugs/recpticles or undersized wire. As long as there are...
The install looks real nice. The humidity in my area gets pretty high so moisture in the air is a concern. I used a section of hot water baseboard tubing, the...
The plate is actually the harder part to make. The flywheel is easy if you have a chunk of steel and a lathe. KEP welds 3 pieces together to make theirs. I...
I have finished with the installation of the passenger door (it was a trick mounting the striker plate carrier after installing and adjusting the glass!) and...
Hmmmm, I had not thought of putting several pieces together for the flywheel. Ill have to give that some more thought. I have a lathe that is big enough to...
Wayne...Have you changed your email address? I can't reach you. Ben ... From: Wayne Meckling To: loflyin40@yahoogroups.com Sent: Sunday, February 04, 2007 8:50...
I will be interested in a SBC to Audi flywheel, and if you need to see the SBC Chevy to Audi adapter plate from Kennedy I do have one. Thanks Dave Yingst ...
I was just going through manuals a got with my car and I'm very confused. The guy I bought this from said he got it in 1967, it's a three piece without rocker...
The correct wire for any motor circuit per the electrical code is large enough to safely carry 1.5 times the full amperage rating of that motor. Copper Wire GA...
Thanks for the info. My wire running to the compressor is 10 gauge. Not sure on the exact type, but it is wrapped in orange. I think normal operating is at 22...
If your GT-12 has no rocker panels, then it was intended to have the Mustang hinges that tuck the leading edge of the door into the fender. The assembly ...
Thanks Bud, I have all of the manuals, old and new and Valkyrie/chassis. I just wasn't sure which hinge type fits mine. The "B" in the name threw me, I've...
Mike - Hope the compressor is coming along. We are freezing our butts off here in Tucson also. Barely going to make it to 80° today. Clem K. ... From:...
Go ahead, make all is east coast guys feel bad... ... make it to 80° today. ... gauge. ... of ... to ... the ... connectors ... for ... pin ... for ... ...
There is another one on eBay _http://cgi.ebay.com/AVENGER-GT-12-Model-by-IMC-1-25-Sc_W0QQitemZ190080754056Q QihZ009QQcategoryZ2581QQrdZ1QQcmdZViewItem_ ...
OK, the first correct answer to any of following questions gets a "THANK YOU" from me. Check out the photo of the factory assembled one piece Avenger GT-12 in...
Hi Tom, I have installed the early style LTD side glass - Mustang vent window on a late model Avenger long doors no rocker panels. The pictures are posted...
John, I think the indentation you're referring to is Bud's custom made gas filler access door. Regards, Tom Prachick PS I got to see a factory built Avenger at...
Since I used a Corvair bellypan rather than a VW bellypan on my GT-12, the stock location of the Corvair gas filler pipe was at that spot. Since the radius of...
Thanks, Tom and Bud. I suspected it was a flap to access either the master cylinder reservoir or the fuel filler but wanted to know what. On another subject,...
John AOne of the biggest problems I have with my car is door adjustments. I have been known to put the car outside under a cover if something else is going on...
kevin-had the same problem so i drilled 3 1/8" holes thru the door support, door and hinge and use 1/8" welding rod to locate them. i used 3 holes per hinge....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
