I bought at Costco. I have a 66 Avenger. I bought the small cover and it fit good. It is a lined cover. They sell them for around $30. Frank Hoinsky ... uses?...
Luke - I can look it up in the literature I have but need to know the year and is it an Avenger or a Valkyrie?? If it is an Avenger you need to know thw model...
Hi i have a 69? valkire v8 how do i remove engine without removeing front half of body. It looks like i will have to cut rear crosmember ??? thanks bill...
I believe that California Car Covers picked-up the patterns for the Avenger and Jamaican Fiberfab kits. When I ordered mine it was listed as Pattern #502 . I...
The following message was sent to all Group Owners.... I dont know anymore than any of you all do. So Read the message... Rich...... ... We wanted to let you...
After considering some of the suggestions offered, I went to Advance Auto and bought a 10 inch "universal" interior night/day mirror for $13.88. The special...
Thanks for the heads up. ... From: Rich King To: loflyin40@yahoogroups.com Sent: Friday, November 03, 2006 5:08 PM Subject: [loflyin40] FYI for all LoFlyin 40...
California Car Covers still has the Avenger pattern #502. They recommend for indoor : Softweave(grey) $169.99, Plushweave(grey) $179.00 or Dustop(grey,tan)...
Earl is write on that pattern #, as I purchased one when I was in Cal. On vacation in 1978. I could not remember the company that made it. I am still using it,...
Hi Luke - To align my mounting of the rear end and front suspension I used a plumb bob with masking tape on the floor and marked the center line of each axle,...
Did and done . Hope you get it on time. Again - East on Broadway Blvd. , 15 mi from downtown Tucson, to Freeman Road. South 0.9 mile to Twin Hills Trl. West to...
Bob, nice job on your Avenger's rear fender flares. How long has this effort taken you thus far? Did you have a pattern or integrate the fender flares from...
-- to all -- fiberfab made a couple different style rear window louvers - one set ON the body over the rear window - the other set IN and in place of the rear...
I have some marine grade carpet (rubberized backing) which I hope to use for the car. I plan to make patterns first and have two questions - since cardboard...
... this ... see ... filler/sanding ... Thanks Tom, I used spray polyurethane foam,West system epoxy resins and fillers,small amount of bondo and part of...
If you guys havent seen this months issue of kit car magizine- you might want tocheck it out- its actually worth reading this month! they've got several big...
Hey bob, I liked your work. How did you decide the layers of mat or cloth to use? Is the two cloth and matt as strong as the original body? The mat I take it...
Mike : Listen to the voice of experience....always used a layer of mat over any cloth repair. The fiberglass cloth pattern will bleed- thru and be visible a...
Earl, I'm sure you learned a lot of helpful tips from your V-8 Avenger body mods activity (I've been impressed from day one at your in work and finished...
Thanks to Mike Mann , we have a mold from one of his Gurney bubbles. If there is any interest, we will mold a few in late December. If you need the added...
... epoxy.Then ... 2 ... the cloth is always stronger than matte but matte doesn't show texture through the repair.they also make a veil which is even thinner...
Hi Guys, This is one for all the VW guys.I have a fine oil mist coming from the back of my engine somewhere but I cannot find where it is coming from I see no...
Joe, just a wild guess (I have never experienced the problem you describe) but I would suspect the oil cooler. If so, the mist could be distributed by the...
Hey Joe, it's probably coming out the breather tube, is it a stock one? You might want to relieve the rocker covers by inserting vent nipples through the...
Joe, I'm not a VW guy (my air cooled engine has 6 cylinders), but this sounds like a plugged crankcase ventilation system. Under load, blowby from the rings...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
