I am reusing my rx-7 seats in my avenger. They should be able to be adjusted forward and back and recline. http://www.bitinfusion.com/5-06-05/ I took them...
Mike.... Years ago I had a T Bucket roadster that I wanted to get low enough to be behind the 1/2 windshield... Now normally these cars have a plywood seat...
I am now in the process of seat "fitment" - I had hoped to use marine type swivels and slides to allow the passengers to turn and step out rather than twist -...
Mike..... Try this link... You may need to copy and paste it into your browser address line.. This will show you the construction of GT40 Seats that are used...
have a couple of rci race car seats that i'm trying to use. the bottom is very short and needs lengthing to about 19" for thigh support. have a headroom...
To Anyone going to Carlisle but does not have a motel room. I reserved two rooms at the Day's Inn in Carlisle. Our plans have changed & the one room will not...
Jim I am interested whats the cost? we have never been there. Bill 513-608-3858 ... From: jemeyer <jemeyer@...> To: loflyin40@yahoogroups.com Subject:...
Checked the assembly manual for the Valkyrie, and GT15. The only mention of seats for the GT15 is "Bucket Seats" That is sure a big help. If you are looking...
I have tried using honda prelude seats. I'm only 5'7 and with no adjusters and some foam cut out of the bottom they almost work. Mike Erics frame, I take it...
kevin-the frame is flat with a large center tunnel and tapered u shaped channels along the side for mounting the body to. the rear sits higher because i needed...
Well, I welded in the bottom pan. It is pretty thick steel. I went to a steel distributor and they had very little thin guage metal. I have decided to try and...
mike-nice jog! it all depends on how tall you are. as you recline the seat you also run into problems with the slope of the roof. as you look forward you will...
Does anyone have photos in the albums of a car body raised with spacers and how much? I tried to look for these but could not find them. I was thinking of...
Did Fiberfab have their own design front sidemarker lights? I was going to change the ones on my car but they are recessed into the fiberglass and the...
We raised the body in the back of our car 3". The front stayed the same. It is a 1966 Avenger on a 1974 VW frame with cv axles. The suspension was lowered to...
Wayne - I could not find any reference to side marker lights in the Fiberfab "Chassis Preparation" manual. They mention headlights, taillights, courtesty lamp,...
Guys, I have always gone to Carlisle on Saturday but I might try Sunday this year so I was curious... How many people are there on Sunday compared to...
Wayne.... My Car GT12X has a small round lamp with a chrome ring (Soon to be removed)... I suspect that these may be originally Chrysler late 60's to early...
Kevin....Sunday is a dead day. Most of the vendors have left and the crowd is small. A few people hang around to try to win the giveaway car that usually isn't...
can you "tweak" the door on a early like you can a late? the lower rear edge is wraped outwards about 1 1/2 inches. can bend into decent shape but unable to...
Definitely, a little round job, I've seen them on early Chrysler's, '60s to to early '70s like Rich said, my car has the holes, in the front (soon to be closed...
The sidemarker light are off of a Plymouth Satellite. I am not sure which year but I had to have one replaced due to my wreck and they are tough to find. Joe ...
Mike Sounds like your door may be twisted. I had the same problem on a Avenger i had once. I did the rod fix but I didnt have windows in it. I have heard...
Hey fellas, a while back, one of you guys was looking for Chick, well i was with him most of the afternoon today, he still lives in Butler N.J. at 27 Center...
MIKE : In the past,I installed "tweak" rods on the doors of my blue GT-12 Corvair Turbo and they did not interfer with the Ford LTD and Mustang vent window...
thanks for the ideas. had no problems with the drivers door but this thing won't quit. going to form a piece of tubing into the contour that i need and try pop...
