Hi all, Recently, I have some problem with my brake (maybe it's not the brake). I feel some vibration on the steering wheel when I apply brake while the car is...
Orkiddan, Your brake rotors (front) are warped and either require machining or replacing. This is usually caused by one of three reasons: 1. You rest your foot...
Can't comment on the disc problems, but I am using EBC Greenstuff pads on my B4, and am delighted with them. Feel around town is almost identical (only...
Orkidan, I was intending to leave this alone, but can't help myself. My belief is that you are using GREENSTUFF pads? If so, it is my belief that whatever...
Hi I've eventually fixed by Huge VOD, it started at 2800rpm and would only produce .5bar until 4200rpm where it would start to take off. I've tried loads of...
Thank you all for the advice and comments. Paul, I don't think the 3 reasons you stated are the causes for the warping of my disc. Coz they are not my driving...
Hallelujah!! (and I am not just saying that because Japan just drew 2-2 with Belgium! ;- ) ) 200rpm VOD!! Wow - that would be nice to experience!! It's a shame...
Anton
aww@...
Jun 4, 2002 11:11 am
4464
Great news Paul, I reckon I might be having the opposite problem, sort of. My secondary seems to take ages to come in, so maybe I'm not getting enough pressure...
Paul Now fly to perth and fix my problem!!! my primary doesnt come in till 3000ish rpm :( and now the VOD goes to almost zero ( i just got a MBC put on the...
G'day, Was having a play in the car and found that my ECU has a Mine's guarantee plaque on it which I assume means that it has had the VX ROM chip installed in...
Hi Steve, Nice little bonus there! They are JYE 96,000 with trade-in, or 175,000 outright. Has your car got an A/M back box, air filter and a boost gauge? If...
Anton
aww@...
Jun 6, 2002 8:17 am
4468
Hi Anton, I'll have a look tomorrow at the centre pipe. I do have a boost gauge and my turbo timer registers boost and records peak too. I don't find I get ...
Steve, Well, just going by the boost level that sounds like you have a std mid-pipe, but take a look anyway... As for intakes, Paul Hansen had Blitz panel (the...
Anton
aww@...
Jun 6, 2002 11:43 am
4470
Albert, Have you got the article??... Nice looking Rx in deed...are your wheels 18"..? I recall we discussed your Rx before when you first had the work ...
http://www.scoobynet.co.uk/bbs/thread.asp?threadid=102335 not sure what else to advise... is there a good way to test efficient earthing - like with a ...
Paul, I think you have given the best first stop advice, B4 Boy perhaps even needs to reset again to get things clean sheeted...but I have a feeling that he...
Anton
aww@...
Jun 6, 2002 2:00 pm
4473
thanks Anton, I have mailed matt offline to get him to post on here if he is still having probs... by the way you shouldn't be so self-effacing - the quality...
The cotton filters seem to do the best job IMHO. As far as octane boosters are concerned, it's hard to find a good one. IF you can get hold of Methyl Benzine,...
... AFAIK, boost spikes will come up way before redline. Boost starts tapering off towards redline, I think the boost spikes are probably around 5500rpm-ish,...
Paul Hansen
p-hansen@...
Jun 7, 2002 12:45 am
4477
Hi Paul, "K&N is a dry type, but foam filter, correct?" - Wrong :) K&N is the oiled, paper sandwiched between mesh filter. The Zero sports panel filter, is it...
My K&N panel filter is cotton, not sure what other types you guys may be able to get, or hat the other Paul is using. Regards Paul Silver GT Legacy ... From:...
Just on that decel issue - it is the old 200kph+ bogey. When the flow is "too" good, the OE ECU can get horribly flummoxed when the throttle is suddenly closed...
Anton
aww@...
Jun 7, 2002 2:19 am
4480
... Ouch. Not good. I'm probably thinking of HKS, actually, when referring to foam. Oiled paper sandwiched between mesh sounds like a fast path towards AFM...
Paul Hansen
p-hansen@...
Jun 7, 2002 2:20 am
4481
... Yeah, well, I think that's because every B4 owner is warned off doing it - I'm not sure I want to be the beta tester on this one (tho I can't hit...
Paul Hansen
p-hansen@...
Jun 7, 2002 2:24 am
4482
Oops, forgot about the fuelling thing, too. Things can lean out too much with the big ram-pods et al. I have not seen the O2 sensor readings myself, but lean...
Anton
aww@...
Jun 7, 2002 2:34 am
4483
Anyone here a member of the UD project into searching for a cancer Cure? Paul Fenner Business Consultant - Technology IBD / E-Business ? Paul.Fenner@......
Hi All, I was just at the shops and saw the article on Motor Mag (Aussie) about the STI WRX, it had a small section about the STI B4, had a pic of a white B4...
The STI filter I had was foam + s.steel mesh. It also ate my AFS for lunch so stay away from it. (It also took the O2 with it as well.) -Mike ... a layer ... ...
