I know the owner's manual recommends 87 for my '00 GT with the 4.6L V8 but that strikes me as unusual for a high performance car. My wife has a '00 Nissan...
Or Try www.stangparts.com - if they dont have what you are looking for, call them (their number is on their web page) and ask if they know of someone. Page ......
87 octane is fine. We have a 2002 and run 87 with no problms. HAVE to run 91 in our Cobra. To be honest with ya - the 4.6L V8 isnt really what I would call...
First I would like to say that I just joined and hopefully someone knows the answer to my stupid question. My right rear directional is out so I purchased a...
I recently added a Steeda timing adjuster and run 13 degrees timing with 89 octane gas with no problem. Boosting the timing is a good low buck way to add 10 or...
I know it is not a power house but I am getting ready to do a few mods and now I need a new clutch. Any recommendations? Any help is greatly appreciated. ...
Check out www.ddperformance.com Don Walsh has great products and is reasonably priced. mkeschinger <no_reply@yahoogroups.com> wrote:I know it is not a power...
Hello i need help with gears.I have a 99 v6 mustang and i want a set of gears for it what would you guys recomend putting in it i was thinking 3.73 let me...
Go with a K&N air filter. I have have a C&L 70mm mass air meter that fits the Ford 3.8 liter six that will give you 10HP. I will sell it to you for $45.00. It...
Steeda sells the 3.73 gears. From what I have read it is good for 2 tenths off your 1/4 mile. ... [Non-text portions of this message have been removed]...
That place was great. The heavy duty clutch was only 159 for the complete kit (plus shipping of course) The local places wanted close to $300 to replace it...
California Mustang has released its new 1987-1993 Mustang Carbon Fiber hood. But remember California Mustang has been doing Mustangs for over 27 years, they...
Hey all...I am a new member with a '99 Limited Edition performance red coupe. I was wondering if any of you are using the Ford Racing Performance Parts...
Hello all we are looking to find Mustang Club of America members in the Maryland, Northern Virginia and Eastern Pennsylvania areas. If your a member of the MCA...
my 86 gt keep,s having problems with the engin over reving at idle it surges up and down until it finaly stalls how do i fix this a friend told me it may be...
Hello everyone, I found these neat 12" X 18" Mach1 posters :-) Check it out here: http://www.limited-art.com/mustang.html Let me know if you want one! ...
The idle speed is not controlled the regular throttle butterlies, but by a throttle bypass valve that permits airflow around the butterflies when they're...
(no author)
(no email address)
Jan 31, 2003 9:24 pm
1032
Get some cool Mustang window decals http://vinylxpress.net...
I have just acquired a 1988 Mustang G.T. convertible. I am looking for some cool sites to visit for upgrades and parts. I am also looking for technical advice...
All parts are located in Monroe, NC near Charlotte, NC I have a Hurst Quarter Stick used with a brand new cable, new linkage kit to make it work with an AOD...
NEW Edelbrock timing chain part number 7811 1962-65/1973-95 Ford Small block $50 shipped Little used, excellent condition Omega 1.72 bolt down roller rockers...
Cruise Night Anyone? Anyone interested in attending a cruise night? KEG's Bistro in Foothill Ranch (Orange County, CA) is starting Krooze Nights (similar to...
hello i was wondering something.I have a 99 v6 mustang>I took the nasty gay grille out and put mesh in there but now i have those stuppid holes where the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
