Working on my turbo install today. Looking around the internet for the odd sized V-band clamp I need for the compressor discharge on my Holset HX35W. I ran...
I have their 38mm wastegate on my car right now. It works perfectly. ... From: Daniel Nicoson <A6intruder@...> To: Jyturbo <jyturbo@yahoogroups.com> ...
Dave Sitar
tooslowcrapi@...
Jul 1, 2007 4:30 pm
88172
Thanks Dave. I'm setting up to run a Holset HX35W on my 1994 302. Stock bottom end, AFR 165 heads and a "baby Crower cam" (really just a .532" lift version of...
V-8, external waste gate, single turbo, stock left side header feeds a cross-under tube into a log-style manifold on right cylinder bank, turbo turbine housing...
Mine is a 60-1 on a 302. I would think that the 38mm would be enough but the wastegate I bought from then is set up for 9psi. I run 16 or 17 but with the...
Dave Sitar
tooslowcrapi@...
Jul 2, 2007 12:34 pm
88175
That’s kind of what I was thinking. Running lower boost on my 302 will require me to pass more through the waste gate. I’ll probably go with the larger...
I'm getting close to having the big stuff done on my turbo install. Figured I needed to start looking at possible got-ya's. 1994 Mustang GT stock bottom end...
A little late but since I have something potentially useful: Holset... go to your local "Cummins power systems" and buy the correct stainless one, it's...
I just received my 46mm waste gate from these guys. Damn! This thing is big! Another packaging issue. I think that’s the hardest thing on this whole ...
Yeah, I put a 50mm gate on my S-10 because the 35mm did not slow anything down. It would zip right past the boost setting like the gate was not on there. The...
Hrm, don't know about your other electronics, but my brake boosters have a one way valve in them so that they retain vacuum after the car is shut off or under...
Here's a thought. Before I had an intercooler on my car, the brake booster check valve would last about a year. I figure tha extra pressure in the intake was...
Thanks Andrew. I was looking through the Ford manual last night. It looks like most of the systems do have their own check valve. I guess I won’t have to...
Im pretty sure the booster has an inline check valve so it only gets vacuum. . . Kevin ... From: Daniel Nicoson To: Jyturbo Sent: Friday, July 06, 2007 11:43...
What style mufflers have worked well for you guys? I understand that low backpressure after the turbo is the #1 goal. I'm thinking of a simple 3" diameter...
Over the years I have read that pipe wrap is generally bad... Getting most of the plumbing finished on my single turbo Mustang V-8. As you can imagine there...
Oops sent too soon... I'd think about using the wrap on the stuff you want to protect but DO use "ideal" heat shields where possible And if you must wrap, well...
After researching ceramic coatings I have a hard time with why they are better than wraps. The argument is that wrap holds heat in and causes over heating of...
... Good ceramic coatings are inside as well... ... A bit of a non issue, My Capri headers have been wrapped for 8+ years, and haven't rusted through yet... ...
One thing to be careful of here is if you get rid of too much back pressure your Mustang will use lots of oil. I have seen it with Imports time and time again....
I'm not quite sure I agree with your suggestions on backpressure. I don't know of ANY full race turbocharged drag racing or road racing vehicles that...
Your right, less backpressure is good.The turbo itself is a big cause of backpressure. Putting a 12" long 6" diameter downpipe on it would still have ...
I wrapped my logs, down pipes, even turbos with the stuff at one point or another and haven't really seen any issues.. My manifolds really warped the first...
I would think a straight through muffler would be ideal.. Flowmasters are dubbed Flow-stoppers, but I still run them.. My brother has an AWD turbo laser...
I'll admit I settled for the Holset for all the wrong reasons, one was it has a built-in waste gate. Turns out I am using an external waste gate after all. ...
Define "good". I talked to many custom coaters and they all told me the same thing.... ... From: Steve Leitch To: jyturbo@yahoogroups.com Sent: Monday, July...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
