Well as if I didn't have enough things that challenge me, I just sold the M20 wide ration 4 speed to make funds for purchasing a T56 six speed for my project....
Hello I put a T-56 from a LT1 96 Camaro SS into a 1986 Caprice. www.cardomain.com/id/383sowhat It is not too difficult of a swap. My info is coming from the...
Hey guys, i've noticed on ebay that you can get a t3/4 turbo brand new for around 275.00 to 300.00. My question, will a single t3/t4 setup work with a...
Mostly, the combo looks good. The only thing that I would look into is the camshaft. Those specs are awful agressive, especially for a turbo motor. Typically,...
You would need to know the size and trim of the compressor, and the turbine to determine the hp capacity of the turbo. The amount of boost that it "can...
Thanks Guys, Great info on the gearing. I am going to look into the 94 to 97 t56. If I can find a viper t56 (not to exhorbitantly expensive) then I will go...
Nathan, Here is a little info on Pontiacs. They like split lift and duration cams. The lobe center on this cam is a 112 center. I have run this cam on a...
You are forgetting that you are not dealing with a naturally aspirated engine anymore, so the old ball park of longer exhaust duration will not be nearly as...
If you do the search , it is on the blow through carb data base, page 3, about 7 down. and, it is a 428 at 9 psi. I am not trying to be difficult, and I am not...
Thanks Nathan, I will check into a smaller duration cam that fits the bill. I only hit that kind of RPM with my old combination. I will keep this combination...
Keep in mind the Holset’s are huge (physically)! I have one and it is fun trying to fit it in my 1994 Mustang. Dan Nicoson ... From: jyturbo@yahoogroups.com...
I have here a turbo I got off ebay that was supposed to come off a F250. Does anyone know its model number and where I could find more data on it, including...
Sometimes Luck smiles and things just work perfectly. Yesterday I went to a local wrecking yard and scored a complete 9" Ford Rear End for $100 bucks. That...
... Ok, I made a miscalculation. My 9" decoding was a little off. According to a few web sites that I looked at it is either a 3.69 gear or a 3.89 gear....
Hello all, I've been looking at kits on the net for my year and make, cheapest turbo kit that i've found has been just shy of 5 large. Thats just too much for...
You might want to look into Nitrous... ... From: clifton_76 To: jyturbo@yahoogroups.com Sent: Thursday, March 08, 2007 11:30 AM Subject: [jyturbo] Its me...
I wouldn’t add a turbo without the ability to tune your fuel and spark. That’s pretty easy these days on a Mustang, does cost money but so does a rebuild...
I second that. For small HP gains that will not require motor modifications, less work, and ease of installation, Nitrous is the cheapest way to go. Good...
thanks all, I really don't want nitrous, im not going to be going to the strip in the gt, i just want a solid 3-400hp , nitrous may be cheap at first, but if...
... From: "clifton_76" <clifton_76@...> Subject: [jyturbo] Its me agian... ... thing work??? ********* I think you could get about another 25 or 50 hp...
If you are determined to go turbo (not trying to discourage – I love the idea) then I would count on tuning the engine. Do you have to pass smog with that...
I second a trip to www.turbomustangs.com . Usually www.corral.net and www.stangnet.com have good forums as well, but not so much for the DIY/JY turbo group....
I think every electronic boost controller comes with the ability to select multiple boost levels. But the best course of action is to stay out of boost until...
Left foot...ah, you mean under the gas pedal... ... From: Dave McFarland To: jyturbo@yahoogroups.com Sent: Tuesday, March 13, 2007 9:04 AM Subject: Re:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
