... There isnt much that can take out a bearing that quickly. Is it possible that the housing got nicked when removing the outer race? I have seent that ...
D G
jeeprz2@...
Dec 1, 2006 4:06 pm
87372
I'm a long ways from an expert on these things but this occured to me. You put that much power to the ground and get good traction something just might break....
Clutches, atleast the discs never "fly apart" under power. The disc may break but the pieces tend to stay put until the clutch is released. Flywheels and...
Any chance the pinion shaft is slightly bent. I'm sure you guys checked that... Otherwise, would the case be cracked and only open up while driving. Dye ...
Yes but the issue isn't that it broke on the dragrace pass, it's that the guy has subsequently installed fresh parts and is very experienced in the art of ring...
Well this isn't JY related but what the hey- My dad loves a deal, and has been dealing in repairable cars up in Minnesota for years, he buys one from the...
... With the early prototypes of the injected 460engine the engines were making an honest 330hp and WOULD break things in an F350 chassis. Remember it isn't...
Wait till your dad sees it and than if necessary give him your car. He is you daddy after all. My hunting buddies daddy is 85 or so, he had a failed marriage ...
... Ok, I'm not totally familiar with this diff. Is it crush tube or spacer set pinion preload? If it's the former is there any possibility that there's been a...
... I'd do it in that order if possible (sight unseen, usual disclaimers) as heat seems to be the best friend of the guy with a broken or stubborn bolt. Some...
The power steering pump is on the serpentine circuit- no belt, no water pump! So an idler of such has to be there. No, Delta 88's did NOT come without PS. The...
I cant see any easy way to make repair , if you have access then normally a special welding rod would be used after determining the actual block metal used ,...
If getting the tap out fails then Fab a bracket to a different hole (more than one preferably) it's going to be way easier to take a few measurements weld some...
Oh, man!!! Sounds like a really competent, qualified mechanic has been working on this car.... I deal with similar issues at work, (I'm considered a 'problem...
... 1. I don't believe that. Who told you this? A Ford engineer? Name? 2. 330HP doesn't mean anything to me. 330HP at what rpm? 5500? 3000? Since HP is...
I came in on the end of this thread (never saw the original) but as I understand it, the problem is a broken tap that has a little bit sticking up out of the...
... bummer ... How about a thick steel plate that is them wrapped around a couple of water pump bolts then snakes back behind or whereever to attach the pump....
Well I tried welding a nut to the remains of the tap, no success- so, I looked it over with a pal of mine, and the solution now is to bracket the pump off of...
Ok, this really isn't that hard to deal with. Broken tap: - do you have a tap extractor? It's a 3 finger deal that reaches into the flutes of the tap and...
Started my Mustang for the first time in 6 months today. During the 6 months of non-running I changed a hydraulic line on the rack & pinion system. Most of...
It's usually finished bleeding the air out of the system a few minutes after turning off the engine. Sometimes the pump will exhale some froth if it was right...
Thanks Randy & Dave. I was hoping it would be easy! Dan Nicoson ... From: jyturbo@yahoogroups.com [mailto:jyturbo@yahoogroups.com]On Behalf Of Betty Ann Hicks...
I think turn the wheel lock to lock a bunch of times. Kevin ... From: Daniel Nicoson To: Jyturbo Sent: Sunday, December 10, 2006 10:11 PM Subject: [jyturbo]...
Dan, We all know easy never lasts!! The following method helped me beat the clock. I had various reservoir caps to which I attached a small 1/8" tube (epoxy or...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
