... From: "Allan De Groot" <adegroot@...> Years ago in the TransAm series the Traco built DZ302's run in the Penske Camaro were built with 2ring pistons ...
... From: "Mark Pikas" <mpikas@...> ****** When we first started making our toy race cars, we used pourable urethane liquid to mold our tires ... just...
That was exactly my point. I can't look for it from here and I doubt that I'll have time before the end of the week, but the page that I suggested you look...
Now that we are back on turbos I will read the post again! If I wanted to learn about guns (which By the way are trailer mounted or ship mounted Via military...
Tom, Once you do identify the compound properties you are looking for let me know, we have an applications engineer here that I can ask, he may have an idea...
... I'd make you a deal, but I don't think you're endangering the one you have... Once you start increasing the percentage of joy juice, you should see if...
... You might need some acetone to get the model airplane fuel to mix with water. Try mixing some in a bottle and letting it sit overnight to see if you have...
... Manley sold single-ring pistons for a long time. The fad went away, as far as I know. ... I've built a lot of strokers with pinned/unsupported or bridged...
I know this isn't a factory piece, but it's close. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll? ViewItem&category=33742&item=7938021199&rd=1 Not to feed...
At least from a chemical deactivation standpoint. But from a thermal deactivation standpoint it's another story. The chamicals themselves shouldn't hurt the...
What we need here is a "refinance your turbo setup" service...:^) KC ... From: "Allan De Groot" <adegroot@...> To: <jyturbo@yahoogroups.com> Sent: Tuesday,...
Allan, That is why in the original post it said "many will very convincingly argue". There are more pieces of the puzzle then the rings in these debates. I'm a...
Which would support that a short bursting system that supplements normal gasoline operation with a high speed shot should not be a problem, as it starts,...
Well said. _____ From: kenny [mailto:kjboyer2002@...] Sent: 01 December 2004 11:50 To: jyturbo@yahoogroups.com Subject: [jyturbo] thanks for getting back...
I'm pondering designs for my weld el turbo manifold, and I'm wondering if there is a source for straight pipe that fits the ID and OD dimensions of common weld...
I'll try to find mine and take a pic of it, but its just a flange with about a 1/2" tube coming off. It actually comes straight out about a 1/2" and then...
I'm pretty sure that McMaster-Carr carries straight sections of "weld el" material, in matching wall thicknesses and diameters. I recall seeing it in one of...
I've heard you can drill a hole in the body of a mechanical fuelpump, mount a fitting and run it to the discharge side of the turbo which will raise the fuel...
You're partially right. Mechanical fuel pumps are pressure referenced to the atmosphere and via a vent hole in the diaphragm housing. This is probably what you...
I've got one of those 2-wheel wheelbarrows, and I've managed to bend the damn axle on the thing - cheap Home Depot crap! I've already bent in back in place...
... I've always assumed it was a weep hole because I thought this was to prevent fuel from being pumped into the crankcase if the diaphram failed. This was...
I've heard of special one-off taillights made in the microwave. Does anyone know about that procedure? Will it also be something to try on standard ...
I can just build that into the spark tables. I set the onset of nitro injection based on the fuel injector pulse width (LOAD) so I just up that corresponding...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
